< Back ×
My Vehicle Change Vehicle
2008 Chevrolet Impala
< Back to View All
Ignition, Distributors & ECM
- Department
- Prices
OEM (Genuine) 2008 Chevrolet Impala Case
PartNumber: 19149552
Product Specifications- Notes: Column Shift; Floor Shift
- Other Names: Case, Ignition Lock
- Item Dimensions: 6.2 x 5.4 x 5.1 inches
- Item Weight: 1.60 Pounds
- Fitment Type: Direct Replacement
- Replaces: 19133760
- Part Description: 2008 Chevrolet Impala Case
Vehicle Fitment- 2008 Chevrolet Impala | 50th Anniversary Edition, LS, LT, LTZ, Police, SS | 6 Cyl 3.5 L FLEX, 6 Cyl 3.5 L GAS, 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS, 6 Cyl 3.9 L FLEX, 6 Cyl 3.9 L GAS, 8 Cyl 5.3 L GAS
$59.04 MSRP:$111.42You Save: $52.38 (48%)
OEM (Genuine) 2008 Chevrolet Impala Cylinder Kit, Ignition Lock
PartNumber: 15794826
Product Specifications- Notes: Column Shift; Floor Shift
- Item Dimensions: 3.2 x 2.2 x 1.8 inches
- Item Weight: 0.70 Pounds
- Fitment Type: Direct Replacement
- Replaces: 25756079, 19120038
- Part Description: 2008 Chevrolet Impala Cylinder Kit, Ignition Lock
Vehicle Fitment- 2008 Chevrolet Impala | 50th Anniversary Edition, LS, LT, LTZ, Police, SS | 6 Cyl 3.5 L FLEX, 6 Cyl 3.5 L GAS, 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS, 6 Cyl 3.9 L FLEX, 6 Cyl 3.9 L GAS, 8 Cyl 5.3 L GAS
FAQ for Ignition Lock Cylinder Repair
Q: What should you be careful about when I stake the cap onto the head of the case?
A:
You should be careful not to scratch or dent the cosmetic surface of the cap or damage the lock cylinder in any way while staking the cap.
By Bob
GM Specialist
01/11/2022Q: What's the tip for removing the ignition lock cylinder?
A:
You shall pull the ignition lock cylinder from the steering column.
By Bob
GM Specialist
01/11/2022Q: What should be noticed when you install the turn signal switch housing?
A:
You will need to press the turn signal switch housing firmly against the steering column tilt head for the screws from the turn signal and multifunction switch assembly to align.
By Bob
GM Specialist
01/11/2022Q: What should be noticed when servicing the front side door lock cylinder?
A:
The front side door lock cylinder tumblers are not self-retaining and must be held in place if the key is not fully inserted into the lock cylinder or until the cylinder is assembled into the case assembly.
By Bob
GM Specialist
01/11/2022Q: What's the recommended torque for the 3 TORX(R) screws screwed into the ignition lock cylinder case?
A:
The recommended torque is 7 N.m (62 lb in).
By Bob
GM Specialist
01/11/2022Q: What's the preliminary procedure for replacing the ignition lock cylinder?
A:
You will need to disconnect the negative battery cable, disable the SIR system, and remove the tilt lever, the steering wheel, and the steering column trim covers.
By Bob
GM Specialist
01/11/2022See more FAQs (1)