< Back ×
My Vehicle Change Vehicle
2000 Chevrolet Blazer
< Back to View All
Ignition, Distributors & ECM
- Department
- Brands
- Prices
Delphi® Ignition Distributor for 2000 Chevrolet Blazer
PartNumber: CZ20007Product Specifications- Advance Type: Computer Controlled
- Coil Wire Included: No
- Color: Black
- Distributor Cap Included: Yes
- Grade Type: Regular
- Ignition Coil Included: No
- Ignition Rotor Included: Yes
- Interface Description: 3 Pin Sealed Connector, 1 HV tower to Coil, 6 HV Tower to Plugs via Wire Sets
- Operation Type: HVS Distributor
- UPC: 689604125373
- Part Description: 2000 Chevrolet Blazer Ignition Distributor
Vehicle Fitment- 2000 Chevrolet Blazer | LT | All Engines
- 2000 Chevrolet Blazer | Trailblazer | All Engines
$185.25
Cardone Reman® Remanufactured Electronic Distributor for 2000 Chevrolet Blazer
PartNumber: 30-1639Product Specifications- Notes: Electronic Distributor
- Coil Wire: No
- Color: Black
- Cylinders: 6
- Distributor Cap: No
- Distributor Type: Hall Effect
- Electronic Module Supplied: No
- Ignition Rotor: No
- Integrated Ignition Coil: No
- Part Description: 2000 Chevrolet Blazer Remanufactured Electronic Distributor
Vehicle Fitment- 2000 Chevrolet Blazer | All Trims | 6 Cyl 4.3L
$70.58
OEM (Genuine) 2000 Chevrolet Blazer Distributor Asm
PartNumber: 12598210
Product Specifications- Other Names: Distributor, Distributor Assembly
- Item Dimensions: 15.5 x 8.0 x 5.4 inches
- Item Weight: 2.70 Pounds
- Fitment Type: Direct Replacement
- Replaces: 1104057, 93441559, 01104078, 01104050, 01104057, 1104078, 1104050
- Part Description: 2000 Chevrolet Blazer Distributor Asm
Vehicle Fitment- 2000 Chevrolet Blazer | Base, LS, LT, Trailblazer, Xtreme, ZR2 | 6 Cyl 4.3 L GAS
Spectra Premium® Distributor for 2000 Chevrolet Blazer
PartNumber: GM02Product Specifications- UPC: 874183001792
- Part Description: 2000 Chevrolet Blazer Distributor
Vehicle Fitment- 2000 Chevrolet Blazer | All Trims | 6 Cyl 4.3L
FAQ for Distributor Repair
Q: What holes should the rotor be removed from?
A:
The rotor was removed from the rotor screw holes and the rotor locator pin holes.
By Bob
GM Specialist
29/10/2022Q: What is the recommended torque for two new distributor cap screws?
A:
It is 2.4 N.m (21 lb in).
By Bob
GM Specialist
29/10/2022Q: What is the proper position for the driven gear?
A:
The dimple will be approximately 180 degrees opposite the rotor segment when the driven gear is installed in the distributor.
By Bob
GM Specialist
29/10/2022Q: How to remove the spark plug wires from the distributor cap?
A:
You need to twist each spark plug boot 1/2 turn and pull only on the wire boot to remove the wire from the distributor cap.
By Bob
GM Specialist
29/10/2022Q: Under what circumstances should I replace the cap and the rotor?
A:
You don't need to replace them unless there is a drivability concern.
By Bob
GM Specialist
29/10/2022Q: Which Installation Procedure should I choose when the crankshaft has NOT been rotated from the original position?
A:
You should choose Installation Procedure 1.
By Bob
GM Specialist
29/10/2022Q: What is the recommended torque for the rotor hold-down screws?
A:
The recommended torque is 1.9 N.m (17 lb in).
By Bob
GM Specialist
29/10/2022Q: What is the recommended step for inspecting the shaft?
A:
You need to inspect the housing for cracks or damage and then insert the shaft in the housing. Finally, you need to replace the housing assembly, if the shaft wobbles.
By Bob
GM Specialist
29/10/2022Q: What is the recommended torque for the distributor mounting clamp bolt?
A:
It is 25 N.m (18 lb-ft).
By Bob
GM Specialist
29/10/2022Q: What is the recommended torque for the new screws for the camshaft position?
A:
The recommended torque is 2.2 N.m (19 lb in).
By Bob
GM Specialist
29/10/2022See more FAQs (5)