Contact Us Live Chat or 1-888-220-8330
Search Bar
Search by Part Number or Keywords
  • My Garage
  • My Account
  • Cart
  • Body & Mirrors
  • Chassis & Brakes
  • Engine & Drivetrain
  • Electrical & Lighting
Help Center
< Back ×
  • Body & Mirrors
  • Chassis & Brakes
  • Engine & Drivetrain
  • Electrical & Lighting
Login/Register My Account Track Order Help Center Contact Us
Replacement and OEM Parts for 2000 Chevrolet Blazer Fuel Line Connector

2000 Chevrolet Blazer Fuel Line Connector

My Vehicle Change Vehicle
2000 Chevrolet Blazer
Change Vehicle
Vehicle Options
We need more information about your vehicle to make a correct determination of fitment
< Back to View All
Fuel Systems
  • Department
  • Brands
  • Prices

2 Products found

3 Q&A for Fuel Line Connector Repair
Show Item:
  • 30
  • 60
  • 90
Sort by:
Recommended
Filter
Sort
View by
  • Dorman Inlet Fuel Line Connector for 2000 Chevrolet Blazer - 800-058

    Dorman® Inlet Fuel Line Connector for 2000 Chevrolet Blazer

    PartNumber: 800-058
    Product Specifications
    • Notes: Outlet; Nylon Straight; 3/8 x 3/8; Pkg Quantity: 1; Packaging Type: Bag
    • Fitting Attachment End 1: Quick Disconnect
    • Fitting Attachment End 2: None
    • Fitting Size End 1: 3/8''
    • Fitting Size End 2: 3/8''
    • Fuel Line Connector Design: Quick Disconnect
    • Gasket Material: Rubber
    • Material: Plastic
    • Package Quantity: 1
    • Packaging Type: Bag
    • UPC: 019495025894
    • Part Description: 2000 Chevrolet Blazer Inlet Fuel Line Connector
    More Info
    Vehicle Fitment
    • 2000 Chevrolet Blazer | All Trims | All Engines
    $19.13
  • Dorman Inlet Fuel Line Connector for 2000 Chevrolet Blazer - 800-059

    Dorman® Inlet Fuel Line Connector for 2000 Chevrolet Blazer

    PartNumber: 800-059
    Product Specifications
    • Notes: Outlet; Nylon Elbow; 3/8 x 3/8; Pkg Quantity: 1; Packaging Type: Bag
    • Fitting Attachment End 1: Quick Disconnect
    • Fitting Attachment End 2: None
    • Fitting Size End 1: 3/8''
    • Fitting Size End 2: 3/8''
    • Fuel Line Connector Design: Quick Disconnect
    • Gasket Material: Rubber
    • Material: Plastic
    • Package Quantity: 1
    • Packaging Type: Bag
    • UPC: 019495025979
    • Part Description: 2000 Chevrolet Blazer Inlet Fuel Line Connector
    More Info
    Vehicle Fitment
    • 2000 Chevrolet Blazer | All Trims | All Engines
    $18.73

FAQ for Fuel Line Connector Repair

Q: How to remove the Quick Connect Fitting?
A:
You need to relieve the fuel system pressure before servicing any fuel system connection. Then you need to blow any dirt out of the quick-connect fitting and you need to use compressed air to do this. After that, you need to squeeze the plastic retainer release tabs. Finally, you need to pull the connection apart.
By Bob
GM Specialist
01/11/2022
Q: How to install the Quick Connect Fitting?
A:
You need to apply a few drops of clean engine oil to the male pipe end. Then you need to push both sides of the fitting together to cause the retaining tabs to snap into place. After that, you need to pull on both sides of the fitting to make sure the connection is secure. Finally, you should install the retainer to quick-connect fitting.
By Bob
GM Specialist
01/11/2022
Q: Which tool is required during the procedure?
A:
You need to prepare a J 37088-A Fuel Line Quick-Connect Separator.
By Bob
GM Specialist
01/11/2022

FAQ for Other Repair Info

Q: How to remove the Fuel Tank Pressure Sensor?
A:
You need to disconnect the negative battery cable and relieve the fuel pressure. Then you need to drain the fuel tank and remove it. After that, you need to disconnect the Fuel Tank Pressure Sensor electrical connector. Finally, you can remove the fuel tank pressure sensor from the fuel sender assembly.
Q: How to remove the Fuel Pressure Regulator?
A:
You need to remove the upper intake manifold assembly, and the Fuel Pressure Regulator retainer clip, and you should pull and twist the fuel pressure regulator to remove the fuel pressure regulator from the fuel pressure regulator housing using a shop towel to catch any spilled fuel. Then you need to remove the regulator seal lower O-ring and the regulator assembly filter. After that, you need to remove the regulator seal upper O-ring and remove the regulator seal backup ring. Finally, you need to cover the fuel pressure regulator housing to prevent contamination from entering the fuel system, then you can discard the O-rings.
Q: What is the recommended torque for the injector retainer lock nuts?
A:
It is 3 N.m (27 lb in).