Search Bar
Search by Part Number, Part Name, or Vehicle
  • My Garage
  • Cart
  • OE Parts
  • Body & Mirrors
  • Chassis & Brakes
  • Engine & Drivetrain
  • Electrical & Lighting
Help Center
< Back ×
  • Shop OE Parts
  • Shop By Category
  • Body & Mirrors
  • Chassis & Brakes
  • Engine & Drivetrain
  • Electrical & Lighting

2001 Chevrolet Venture Camber and Alignment Kit

My Vehicle Change Vehicle
2001 Chevrolet Venture
Change Vehicle
Vehicle Options
We need more information about your vehicle to make a correct determination of fitment
< Back to View All
Alignment Kits
  • Department
  • Prices

1 Product found

5 Q&A for Camber and Alignment Kit Repair
Sort by:
Recommended
Filter Results
Sort
View by
  • OEM 2001 Chevrolet Venture U-Bolt Nut - 11516382
    OEM 2001 Chevrolet Venture U-Bolt Nut Diagram - 11516382
    View Related Parts

    OEM (Genuine) 2001 Chevrolet Venture U-Bolt Nut

    PartNumber: 11516382
    $1.14 MSRP: $1.88
    You Save: $0.74 (40%)
    Product Specifications
    • Location: Driver Side; Passenger Side
    • Item Dimensions: 4.2 x 3.0 x 0.7 inches
    • Item Weight: 0.70 Pounds
    • Fitment Type: Direct Replacement
    • Replaces: 22123946, 15702050, 15048124, 14013439
    • Part Description: 2001 Chevrolet Venture U-Bolt Nut
    More Info
    Vehicle Fitment
    • 2001 Chevrolet Venture | Base, LS, LT, Plus, Value, Warner Bros. | 6 Cyl 3.4 L GAS

FAQ for Camber and Alignment Kit Repair

Q: How to handle it when the strut lower hole is not oblong?
A:
You need to remove the strut from the vehicle, secure the strut in a vise, then file the strut lower hole laterally to allow for camber adjustment, install the strut to the vehicle, and install the strut bolts.
By Bob
GM Specialist
01/11/2022
Q: What is the recommended torque for the strut lower nuts?
A:
The recommended torque is 123 Nm (90 ft. lbs.).
By Bob
GM Specialist
01/11/2022
Q: How to measure the front and rear alignment angles?
A:
You need to install the alignment equipment according to the manufacturer's instructions, next jounce the front and the rear bumpers 3 times before checking the wheel alignment, then measure the alignment angles and record the readings, and finally adjust alignment angles to vehicle specification, if necessary.
By Bob
GM Specialist
01/11/2022
Q: What is the recommended torque for the left and right tie rod jam nuts?
A:
The recommended torque is 68 Nm (50 ft. lbs.).
By Bob
GM Specialist
01/11/2022
Q: How to adjust the front wheel toe?
A:
You need to remove the power steering gear seal small clamps, verify that the steering wheel is centered and the wheels are in the straight-ahead position, loosen the left and right tie rod jam nuts, then rotate the inner tie rods to obtain the proper toe angle of O degrees, install the tie rod end jam nuts, and the power steering gear seal small clamps.
By Bob
GM Specialist
01/11/2022

FAQ for Other Repair Info

Q: What kind of special tools will be required in the replacement of the park brake cable-rear (drum brake)?
A:
The tools required include J37043 Parking Brake Cable Release Tool.
Q: How to install the steering knuckle?
A:
You need to install the knuckle, install the bolts that connect the strut to the knuckle, install the outer tie rod to the Steering Knuckle, connect the front lower control arm ball stud to the knuckle, then install the front wheel drive shaft bearing, and the tire and wheel assembly.
Q: How to install the wheel cylinder?
A:
You need to apply LOCTITE GM P/N 12345382 (or equivalent) to the Wheel Cylinder shoulder face which contacts the backing plate, spread the brake shoes apart, install the wheel cylinder, and the wheel cylinder bolts, then remove the cap from the brake pipe and install the brake pipe to the wheel cylinder, bleed the hydraulic brake system at the wheel cylinder, install the brake drum, install the tire and wheel, then lower the vehicle.