< Back ×
My Vehicle Change Vehicle
2001 Chevrolet Venture
< Back to View All
Steering Racks & Gearboxes
- Department
- Prices
OEM (Genuine) 2001 Chevrolet Venture Gear Kit, Steering (Remanufacture)
PartNumber: 19330434
Product Specifications- Notes: Remanufactured, W/O AWD; All Models; W/O AWD
- Item Dimensions: 51.3 x 11.1 x 6.2 inches
- Item Weight: 19.00 Pounds
- Fitment Type: Direct Replacement
- Replaces: 26053458
- Part Description: 2001 Chevrolet Venture Gear Kit, Steering (Remanufacture)
Vehicle Fitment- 2001 Chevrolet Venture | Base, LS, LT, Plus, Value, Warner Bros. | 6 Cyl 3.4 L GAS
FAQ for Steering Gearbox Repair
Q: What is the recommended torque for the valve end fittings?
A:
The recommended torque is 16.9 Nm (12.6 ft. lbs.).
By Bob
GM Specialist
01/11/2022Q: What is the recommended torque for the adjuster plug lock nut?
A:
The recommended torque is 68 Nm (50 ft. lbs.).
By Bob
GM Specialist
01/11/2022Q: What kind of special tools will be required when serving the rack and pinion boot-off vehicle?
A:
The tools required include J22610 Service Boot Clamp Installer.
By Bob
GM Specialist
01/11/2022Q: How to install the rack and pinion boot-off vehicle?
A:
You need to install the new boot clamp onto the rack and pinion boot, apply grease to the inner tie rod assembly and the rack and pinion gear assembly, install the rack and pinion boot onto the inner tie rod assembly, then install the rack and pinion boot onto the gear assembly until the rack and pinion boot is seated in the gear assembly groove, install the boot clamp on the rack and pinion boot, crimp the boot clamp, pinch the pliers together on the rack and pinion boot to install the tie rod end clamp, then install the hex jam nut to the inner tie rod assembly, finally assemble the outer tie rod assembly.
By Bob
GM Specialist
01/11/2022Q: How to remove the power steering gear?
A:
You need to remove the stabilizer shaft, remove the tie rod ends from the steering knuckles, remove the steering intermediate shaft from the steering gear, then support the frame, remove and discard the frame rear bolts, lower the frame and the powertrain, and remove the power steering gear cooler pipe from the steering gear, remove the power steering gear pressure hose from the power steering gear, remove the power steering gear bolts and nuts, then remove the power steering gear through the vehicle left side wheel opening.
By Bob
GM Specialist
01/11/2022Q: How to remove the inner tie rod assembly from the rack assembly?
A:
You need to place a wrench on the flats of the rack assembly, then place another wrench on the flats of the inner tie rod housing, and rotate the inner tie rod housing counterclockwise until the inner tie rod separates from the rack.
By Bob
GM Specialist
01/11/2022Q: What kind of special tools will be required when serving the steering gear stub shaft seals and bearing?
A:
The tools required include J29810 Stub Shaft Seal Protector.
By Bob
GM Specialist
01/11/2022Q: How to adjust the steering gear?
A:
You need to loosen the adjuster plug lock nut, turn the adjuster plug clockwise until the adjuster plug bottoms in the gear assembly, then turn the adjuster plug back 50 degrees to 70 degrees (approximately one flat), and install the adjuster plug lock nut to the adjuster plug.
By Bob
GM Specialist
01/11/2022Q: What is the recommended torque for the inner tie rod?
A:
The recommended torque is 100 Nm (74 ft. lbs.).
By Bob
GM Specialist
01/11/2022Q: What is the recommended torque for the cylinder end fittings?
A:
The recommended torque is 27 Nm (20 ft. lbs.).
By Bob
GM Specialist
01/11/2022See more FAQs (9)