< Back ×
My Vehicle Change Vehicle
2004 Buick Rendezvous
< Back to View All
Alignment Kits
- Department
- Prices
OEM (Genuine) 2004 Buick Rendezvous U-Bolt Nut
PartNumber: 11516382
Product Specifications- Location: Passenger Side; Driver Side
- Item Dimensions: 4.2 x 3.0 x 0.7 inches
- Item Weight: 0.70 Pounds
- Fitment Type: Direct Replacement
- Replaces: 22123946, 15702050, 15048124, 14013439
- Part Description: 2004 Buick Rendezvous U-Bolt Nut
Vehicle Fitment- 2004 Buick Rendezvous | CX, CX Plus, CXL, CXL Plus, Ultra | 6 Cyl 3.4 L GAS, 6 Cyl 3.5 L GAS, 6 Cyl 3.6 L GAS
$1.10 MSRP:$1.74You Save: $0.64 (37%)
OEM (Genuine) 2004 Buick Rendezvous Adjust Bolt
PartNumber: 11562165
Product Specifications- Location: Driver Side; Passenger Side
- Other Names: Adjust Bolt, Lower Control Arm Adjust Bolt
- Item Dimensions: 6.0 x 2.4 x 2.0 inches
- Item Weight: 0.70 Pounds
- Fitment Type: Direct Replacement
- Replaces: 10254819
- Part Description: 2004 Buick Rendezvous Adjust Bolt
Vehicle Fitment- 2004 Buick Rendezvous | CX, CX Plus, CXL, CXL Plus, Ultra | 6 Cyl 3.4 L GAS, 6 Cyl 3.5 L GAS, 6 Cyl 3.6 L GAS
$23.30 MSRP:$39.51You Save: $16.21 (42%)
OEM (Genuine) 2004 Buick Rendezvous Adjust Cam
PartNumber: 10254818
Product Specifications- Location: Passenger Side; Driver Side
- Other Names: Adjust Cam, Lower Control Arm Adjust Cam
- Item Dimensions: 2.3 x 2.2 x 1.1 inches
- Item Weight: 0.50 Pounds
- Fitment Type: Direct Replacement
- Part Description: 2004 Buick Rendezvous Adjust Cam
Vehicle Fitment- 2004 Buick Rendezvous | CX, CX Plus, CXL, CXL Plus, Ultra | 6 Cyl 3.4 L GAS, 6 Cyl 3.5 L GAS, 6 Cyl 3.6 L GAS
$6.43 MSRP:$10.62You Save: $4.19 (40%)
OEM (Genuine) 2004 Buick Rendezvous Bolt, Rear Axle
PartNumber: 22629930
Product Specifications- Location: Driver Side; Passenger Side
- Item Dimensions: 5.1 x 3.6 x 2.1 inches
- Item Weight: 1.30 Pounds
- Fitment Type: Direct Replacement
- Part Description: 2004 Buick Rendezvous Bolt, Rear Axle
Vehicle Fitment- 2004 Buick Rendezvous | CX, CX Plus, CXL, CXL Plus, Ultra | 6 Cyl 3.4 L GAS, 6 Cyl 3.5 L GAS, 6 Cyl 3.6 L GAS
FAQ for Camber and Alignment Kit Repair
Q: What is the recommended torque for the jam nut?
A:
The recommended torque is 62 Nm (45 ft. lbs.).
By Bob
GM Specialist
01/11/2022Q: What should I do if the strut lower hole is not oblong?
A:
You should remove the strut from the vehicle, secure the strut in a vise, file the strut lower hole laterally to allow for camber adjustment, install the strut to the vehicle and install the strut bolts.
By Bob
GM Specialist
01/11/2022Q: What should be done before measuring the trim height?
A:
You should ensure that the fuel level is a minimum of 1/8 of a full tank, ensure that the correct size tires are on the vehicle, set the tire pressures to the pressure shown on the tire placard, make sure the vehicle is on a level surface and close the doors, the hood and the liftgate.
By Bob
GM Specialist
01/11/2022Q: What is the installation procedure for the rear camber?
A:
You should tighten the lower control arm mounting nuts and test drive the vehicle.
By Bob
GM Specialist
01/11/2022Q: What is the recommended torque for the strut lower nuts?
A:
The recommended torque is 123 Nm (91 ft. lbs.).
By Bob
GM Specialist
01/11/2022Q: How to measure the front and rear alignment angles?
A:
You can install the alignment equipment according to the manufacturer's instructions, jounce the front and the rear bumpers 3 times before checking the wheel alignment, measure the alignment angles, and record the readings.
By Bob
GM Specialist
01/11/2022Q: What should be noticed when measuring the trim height?
A:
You should notice that all trim height measurements are taken vertically to the ground. Trim height measurements within 10 mm (0.4 inches) are considered correct.
By Bob
GM Specialist
01/11/2022See more FAQs (2)