< Back ×
My Vehicle Change Vehicle
2004 Buick Rendezvous
< Back to View All
Lift Supports
- Department
- Brands
- Prices
StrongArm® Hood Lift Support for 2004 Buick Rendezvous
PartNumber: 4359Product Specifications- Body: 19.00
- BODY CONNECTION: ball socket (nylon) 10mm
- Brackets: No
- Compressed Length: 10.81
- Extended Length: 15.56
- Force: 58.00
- Hardware Kit: No
- High Performance Item: N
- Internal Springs: No
- Is Application Specific: Y
- Material: Heavy gauge steel pressure tube provides long life; Rubber o-ring piston seal for controlled lift; Teflon backup ring gives enhanced performance
- Shaft: 8.00
- SHAFT CONNECTION: ball socket (nylon) 8mm
- Stroke: 4.75
- UPC: 043645724818
- Part Description: 2004 Buick Rendezvous Hood Lift Support
Vehicle Fitment- 2004 Buick Rendezvous | All Trims | All Engines
$14.10
OEM (Genuine) 2004 Buick Rendezvous Support Rod Holder
PartNumber: 15571260
Product Specifications- Item Dimensions: 4.7 x 3.9 x 1.8 inches
- Item Weight: 0.40 Pounds
- Fitment Type: Direct Replacement
- Part Description: 2004 Buick Rendezvous Support Rod Holder
Vehicle Fitment- 2004 Buick Rendezvous | CX, CX Plus, CXL, CXL Plus, Ultra | 6 Cyl 3.4 L GAS, 6 Cyl 3.6 L GAS
OEM (Genuine) 2004 Buick Rendezvous Strut, Hood
PartNumber: 10354217
Product Specifications- Location: Driver Side; Passenger Side
- Other Names: Lift Cylinder
- Item Dimensions: 4.9 x 4.7 x 18.9 inches
- Item Weight: 0.70 Pounds
- Fitment Type: Direct Replacement
- Replaces: 10314094, 10422408
- Part Description: 2004 Buick Rendezvous Strut, Hood
Vehicle Fitment- 2004 Buick Rendezvous | CX, CX Plus, CXL, CXL Plus, Ultra | 6 Cyl 3.4 L GAS, 6 Cyl 3.5 L GAS, 6 Cyl 3.6 L GAS
OEM (Genuine) 2004 Buick Rendezvous Rod Asm-Hood Hold Open
PartNumber: 10334868
Product Specifications- Item Dimensions: 35.5 x 4.2 x 3.8 inches
- Item Weight: 0.40 Pounds
- Part Description: 2004 Buick Rendezvous Rod Asm-Hood Hold Open
Vehicle Fitment- 2004 Buick Rendezvous | CX, CX Plus, CXL, CXL Plus, Ultra | 6 Cyl 3.4 L GAS, 6 Cyl 3.6 L GAS
FAQ for Hood Lift Support Repair
Q: What is the proper way to install the assist rod?
A:
The proper way is to press the upper end of the assist rods onto the ball joint on the hood, press the lower end of the assist rods onto the ball joint on the lower hood hinge, remove the support from the hood and close the hood.
By Bob
GM Specialist
01/11/2022Q: What should be noticed when servicing the assist rod?
A:
You should notice that when a hood hold open device is being removed or installed, provide alternate support to avoid the possibility of damage to the vehicle or personal injury.
By Bob
GM Specialist
01/11/2022