< Back ×
2004 Cadillac SRX Steering Knuckle
My Vehicle Change Vehicle
2004 Cadillac SRX
< Back to View All
Control Arms & Suspension Rods
- Department
- Prices
OEM (Genuine) 2004 Cadillac SRX Knuckle
PartNumber: 25998394$109.71 MSRP:$180.37You Save: $70.66 (40%)Product Specifications- Notes: 2WD; AWD; Srx; Right
- Location: Passenger Side
- Other Names: Knuckle
- Item Dimensions: 10.1 x 7.4 x 24.3 inches
- Item Weight: 20.10 Pounds
- Fitment Type: Direct Replacement
- Replaces: 18048937
- Part Description: 2004 Cadillac SRX Knuckle
Vehicle Fitment- 2004 Cadillac SRX | Base | 6 Cyl 3.6 L GAS, 8 Cyl 4.6 L GAS
OEM (Genuine) 2004 Cadillac SRX Knuckle
PartNumber: 88952000$153.50 MSRP:$254.07You Save: $100.57 (40%)Product Specifications- Notes: Srx; Right
- Location: Passenger Side
- Other Names: Knuckle
- Item Dimensions: 11.8 x 11.3 x 9.3 inches
- Item Weight: 11.40 Pounds
- Fitment Type: Direct Replacement
- Part Description: 2004 Cadillac SRX Knuckle
Vehicle Fitment- 2004 Cadillac SRX | Base | 6 Cyl 3.6 L GAS, 8 Cyl 4.6 L GAS
OEM (Genuine) 2004 Cadillac SRX Knuckle
PartNumber: 25998393$113.08 MSRP:$180.37You Save: $67.29 (38%)Product Specifications- Notes: 2WD; AWD; Srx; Left
- Location: Driver Side
- Other Names: Knuckle
- Item Dimensions: 23.6 x 10.5 x 5.0 inches
- Item Weight: 19.80 Pounds
- Fitment Type: Direct Replacement
- Replaces: 18048936
- Part Description: 2004 Cadillac SRX Knuckle
Vehicle Fitment- 2004 Cadillac SRX | Base | 6 Cyl 3.6 L GAS, 8 Cyl 4.6 L GAS
- Product Specifications
- Notes: Srx; Left
- Location: Driver Side
- Other Names: Knuckle
- Item Dimensions: 14.5 x 10.6 x 6.7 inches
- Item Weight: 8.90 Pounds
- Fitment Type: Direct Replacement
- Part Description: 2004 Cadillac SRX Knuckle
Vehicle Fitment- 2004 Cadillac SRX | Base | 6 Cyl 3.6 L GAS, 8 Cyl 4.6 L GAS
FAQ for Steering Knuckle Repair
Q: What tool can you use to disconnect the tie rod from the steering knuckle?
A:
You can use the J 24319-B.
By Bob
GM Specialist
02/11/2022Q: What will be replaced if the torque is at specification?
A:
The dealers will replace the nut/washer assembly only.
By Bob
GM Specialist
02/11/2022Q: What tool can you use to disengage the wheel drive shaft from the wheel bearing/hub?
A:
You can use the J 45859.
By Bob
GM Specialist
02/11/2022Q: What is the recommended torque when installing the large nut on the drive axle?
A:
You can tighten the nut to 160 Nm (118 lb-ft).
By Bob
GM Specialist
02/11/2022Q: What is the recommended torque when installing a new wheel drive shaft nut?
A:
You can tighten the nut to 160 Nm (118 ft. lbs.).
By Bob
GM Specialist
02/11/2022Q: What tool can you use to separate the lower control arm ball stud from the steering knuckle?
A:
You can use the J 43631.
By Bob
GM Specialist
02/11/2022Q: What will be replaced if the torque is not at specification?
A:
The dealers will replace the ball stud, the knuckle, and the nut.
By Bob
GM Specialist
02/11/2022Q: What is the recommended torque when installing the upper ball joint stud to the knuckle, and installing the retaining nut?
A:
You can tighten the nut to 30 Nm (22 lb-ft), and then an additional 180 degrees.
By Bob
GM Specialist
02/11/2022See more FAQs (3)