< Back ×
My Vehicle Change Vehicle
2005 Buick Century
< Back to View All
Trunks & Tailgates
- Department
- Prices
OEM (Genuine) 2005 Buick Century Latch
PartNumber: 16636578
Product Specifications- Location: Passenger Side
- Other Names: Latch, Lock
- Item Dimensions: 6.4 x 3.3 x 3.1 inches
- Item Weight: 1.00 Pounds
- Fitment Type: Direct Replacement
- Replaces: 16629716
- Part Description: 2005 Buick Century Latch
Vehicle Fitment- 2005 Buick Century | Custom, Limited, Special Edition | 6 Cyl 3.1 L GAS
$116.73 MSRP:$176.12You Save: $59.39 (34%)
OEM (Genuine) 2005 Buick Century Lock Solenoid
PartNumber: 16640852
Product Specifications- Other Names: Actuator, Lock Actuator, Lock Solenoid
- Item Dimensions: 8.2 x 3.0 x 3.1 inches
- Item Weight: 0.60 Pounds
- Fitment Type: Direct Replacement
- Replaces: 16632227
- Part Description: 2005 Buick Century Lock Solenoid
Vehicle Fitment- 2005 Buick Century | Custom, Limited, Special Edition | 6 Cyl 3.1 L GAS
$72.42 MSRP:$109.25You Save: $36.83 (34%)
OEM (Genuine) 2005 Buick Century Latch
PartNumber: 10445387
Product Specifications- Other Names: Latch, Lock
- Item Dimensions: 10.3 x 6.3 x 2.8 inches
- Item Weight: 1.20 Pounds
- Fitment Type: Direct Replacement
- Part Description: 2005 Buick Century Latch
Vehicle Fitment- 2005 Buick Century | Custom, Limited, Special Edition | 6 Cyl 3.1 L GAS
OEM (Genuine) 2005 Buick Century Rear Door Latch Actuator
PartNumber: 16636579
Product Specifications- Location: Driver Side
- Other Names: Latch, Lock
- Item Dimensions: 7.8 x 4.6 x 4.6 inches
- Item Weight: 1.50 Pounds
- Fitment Type: Direct Replacement
- Replaces: 16629717
- Part Description: 2005 Buick Century Rear Door Latch Actuator
Vehicle Fitment- 2005 Buick Century | Custom, Limited, Special Edition | 6 Cyl 3.1 L GAS
FAQ for Trunk Lid Latch Repair
Q: How do you install the Latch-Rear Compartment Lid?
A:
You need to position the rear compartment lid latch to the alignment marks on the rear compartment lid, install the rear compartment lid latch to the rear compartment lid nuts, connect the electrical connectors to the rear compartment lid latch and the lock cylinder actuator cable to the lock cylinder and close the rear compartment.
By Bob
GM Specialist
01/11/2022Q: How do you remove the Latch-Rear Compartment Lid?
A:
You need to open the rear compartment, use a grease pencil to mark the location of the rear compartment lid latch to the rear compartment lid, disconnect the electrical connectors from the rear compartment lid latch and the lock cylinder actuator cable from the lock cylinder and remove the rear compartment lid latch to rear compartment lid nuts and the rear compartment lid latch from the rear compartment lid.
By Bob
GM Specialist
01/11/2022Q: What is the recommended torque for the rear compartment lid nuts?
A:
The recommended torque is 10 Nm (89 lb in).
By Bob
GM Specialist
01/11/2022Q: What is the recommended torque for the rear compartment lid lock striker bolts?
A:
The recommended torque is 16 Nm (12 lb-ft).
By Bob
GM Specialist
01/11/2022Q: How do you remove the Lock Striker-Rear Compartment Lid?
A:
You need to pull back the rear compartment trim as required to access the lock striker, use a grease pencil to mark the location of the lock striker to the rear compartment for its location at installation, and remove the bolt from the rear compartment lid lock striker in the rear compartment, the rear bumper fascia, the rear compartment lid lock striker bolts from under the rear bumper fascia above the impact bar to the body panel and the rear compartment lid lock striker from the rear compartment body panel.
By Bob
GM Specialist
01/11/2022Q: How do you install the Lock Striker-Rear Compartment Lid?
A:
You need to position the rear compartment lid lock striker to the rear compartment body panel, install the bolts in the center hole in the rear compartment lid lock striker under the rear bumper fascia above the impact bar to the rear body panel, partially tighten the bolt to allow for adjustment of the rear compartment lid lock striker, close the rear compartment lid and adjust the rear compartment lid striker as required, install the other rear compartment lid lock striker bolts to under the rear bumper fascia above the impact bar to the rear body panel, the bolts to the lock striker in the rear compartment, the rear bumper fascia, and the rear compartment trim and close the rear compartment.
By Bob
GM Specialist
01/11/2022See more FAQs (1)