Search Bar
Search by Part Number, Part Name, or Vehicle
  • My Garage
  • Cart
  • OE Parts
  • Body & Mirrors
  • Chassis & Brakes
  • Engine & Drivetrain
  • Electrical & Lighting
Help Center
< Back ×
  • Shop OE Parts
  • Shop By Category
  • Body & Mirrors
  • Chassis & Brakes
  • Engine & Drivetrain
  • Electrical & Lighting

2005 Buick LeSabre Air Hose

My Vehicle Change Vehicle
2005 Buick LeSabre
Change Vehicle
Vehicle Options
We need more information about your vehicle to make a correct determination of fitment
< Back to View All
Air Filters & Intake Systems
  • Department
  • Brands
  • Prices

2 Products found

2 Q&A for Air Hose Repair
Sort by:
Recommended
Filter Results
Sort
View by
  • Monroe Rear Shock Absorber Air Hose Kit for 2005 Buick LeSabre - AK29

    Monroe® Rear Shock Absorber Air Hose Kit for 2005 Buick LeSabre

    PartNumber: AK29
    $23.65
    Product Specifications
    • Attribute: Air Shock Single Fill Kit
    • UPC: 048598932242
    • Part Description: 2005 Buick LeSabre Rear Shock Absorber Air Hose Kit
    More Info
    Vehicle Fitment
    • 2005 Buick LeSabre | All Trims | All Engines
  • OEM 2005 Buick LeSabre Duct-Rear Intake Air - 12563837
    OEM 2005 Buick LeSabre Duct-Rear Intake Air Diagram - 12563837
    View Related Parts

    OEM (Genuine) 2005 Buick LeSabre Duct-Rear Intake Air

    PartNumber: 12563837
    Product Specifications
    • Other Names: Intake Duct
    • Item Dimensions: 6.6 x 5.9 x 5.8 inches
    • Item Weight: 1.00 Pounds
    • Fitment Type: Direct Replacement
    • Part Description: 2005 Buick LeSabre Duct-Rear Intake Air
    More Info
    Vehicle Fitment
    • 2005 Buick LeSabre | Custom, Limited | 6 Cyl 3.8 L GAS

FAQ for Air Hose Repair

Q: How do I install the Air Tube?
A:
You should connect the air tube to the air dryer, install the air tube with the harness tie and the bolt on the air compressor bracket, install the air tube on the vehicle with three clips, connect the air tube to the left and right rear shock absorbers, install two metal clips on the air tube and the vehicle, install both rear wheels and lower the vehicle.
By Bob
GM Specialist
01/11/2022
Q: How do I remove the Air Tube?
A:
You should raise the vehicle, remove the air tube from the air dryer, remove the bolt and the harness tie from the air compressor bracket, remove both rear wheels, disconnect the air tube from the left and right rear shock absorbers, remove the two metal clips from the air tube and the vehicle and remove the air tube with the three clips from the vehicle.
By Bob
GM Specialist
01/11/2022

FAQ for Other Repair Info

Q: How to install the Accelerator Controls Cable?
A:
You should install the accelerator control cable through the bulkhead, install the snap retainer through the bulkhead, install the accelerator control cable through the slot in the accelerator pedal lever, assemble the dash panel insulator retainer to the accelerator control cable, push (from the passenger compartment) the retainer over cable lever end fitting and up cable until the retainer snaps onto the flange of cable dash fitting, check for complete throttle opening and closing positions by operating the accelerator pedal, install the accelerator control cable to the Throttle Body lever, install the accelerator control cable to the accelerator cable bracket, install the accelerator control cable to the right slot on top of washer bottle, install the accelerator control cable to the retaining clip and install the left closeout/insulator panel.
Q: How do I install the Air Filter Element?
A:
You should install the Air Filter element into the air cleaner assembly, install the air cleaner element cover, secure the air cleaner element cover by pressing down on the retaining clips, and install the intake duct.
Q: How do I remove the manifold absolute pressure (MAP) sensor?
A:
You should turn OFF the ignition, remove the fuel injector sight shield, disconnect the MAP Sensor electrical connector, carefully bend the locking tabs holding the MAP sensor to the PCV valve cover just enough to remove the MAP sensor, and pull the MAP sensor straight out of PCV valve cover.