< Back ×
2005 Buick LeSabre Power Steering Pump
My Vehicle Change Vehicle
2005 Buick LeSabre
< Back to View All
Power Steering Pumps
- Department
- Brands
- Prices
Cardone Reman® Remanufactured Power Steering Pump w/o Reservoir for 2005 Buick LeSabre
PartNumber: 20-542$81.12Product Specifications- Notes: In-Line filter available;For warranty purposes it is recommended to always install a filter and to use suggested OE Fluid and flush the system;Supplied w/o Reservoir
- Hose Port: O-Ring
- Housing Material: Cast Iron
- Import or Domestic: Domestic
- Mounting Hardware: Without
- Power Steering Reservoir Cap: Without
- Pulley: Without
- Pulley Attachment Type: Press-on
- Pump Inlet Attachment Type: Hose Barb
- Pump Outlet Attachment Type: Threaded
- Reservoir: Without
- Thread Size: M16 x 1.5
- Part Description: 2005 Buick LeSabre Remanufactured Power Steering Pump w/o Reservoir
Vehicle Fitment- 2005 Buick LeSabre | All Trims | All Engines
Product Specifications- Notes: Pulley needs to be transferred w/proper pulley removal/install toll.
- UPC: 843613121409
- Part Description: 2005 Buick LeSabre Remanufactured Power Steering Pump
Vehicle Fitment- 2005 Buick LeSabre | All Trims | All Engines
Product Specifications- Notes: Bonneville, Lesabre; 3.8l
- Other Names: Power Steering Pump
- Item Dimensions: 8.2 x 5.3 x 5.3 inches
- Item Weight: 2.20 Pounds
- Fitment Type: Direct Replacement
- Replaces: 26086070
- Part Description: 2005 Buick LeSabre PUMP KIT, P/S
Vehicle Fitment- 2005 Buick LeSabre | Custom, Limited | 6 Cyl 3.8 L GAS
FAQ for Power Steering Pump Repair
Q: How to remove the Power Steering Pump Pulley?
A:
You should remove the drive belt(s), remove the power steering pump and remove the power steering pulley from the power steering pump.
By Bob
GM Specialist
01/11/2022Q: What is the recommended torque when installing the power steering pressure hose to the power steering pump?
A:
The recommended torque is 30 Nm (22 ft. lbs.).
By Bob
GM Specialist
01/11/2022Q: What is the recommended torque when installing the power steering pump retaining bolts?
A:
The recommended torque is 25 Nm (18 ft. lbs.).
By Bob
GM Specialist
01/11/2022Q: What should be noticed in removing the Power Steering Pump?
A:
You should disconnect the power steering return hose from the power steering pump, disconnect the wiring harness from the power steering pump, lower the vehicle and then remove the coolant recovery reservoir.
By Bob
GM Specialist
01/11/2022Q: How to remove the Power Steering Pump Flow Control Valve-Off Vehicle (CB Series)?
A:
You should remove the O-ring union fitting from the hydraulic pump housing assembly, remove the O-ring seal from the O-ring union fitting, remove the control valve assembly and remove the flow control spring.
By Bob
GM Specialist
01/11/2022Q: How to install the Power Steering Reservoir Off Vehicle (CB Series)?
A:
You should install the new O-ring seal onto the neck of the reservoir, install the reservoir onto the hydraulic pump assembly, ensure the reservoir neck is completely engaged onto the hydraulic pump assembly, align the feet of the reservoir with the sides of the hydraulic pump housing, install the new reservoir retaining clips (supplied with the pump).
By Bob
GM Specialist
01/11/2022Q: How to install the Power Steering Pump Pulley?
A:
You should install the power steering pulley to the power steering pump, ensure that the axial tolerance of the power steering pulley on the power steering pump is within 0.25 mm (0.010 inches), install the power steering pump to the engine, install the pump drive belt, bleed the power steering system and inspect the system for leaks.
By Bob
GM Specialist
01/11/2022Q: How to remove the Power Steering Reservoir Off Vehicle (CB Series)?
A:
You should place the hydraulic pump on a fixed, flat surface, with the shaft facing upward, force the retaining clip tab outward, slide the reservoir clip away from the hydraulic pump assembly, repeat the above steps to remove the second reservoir clip, remove the reservoir from the hydraulic pump housing and remove the O-ring seal from the neck of the reservoir or the hydraulic pump housing.
By Bob
GM Specialist
01/11/2022Q: How to install the Power Steering Pump Flow Control Valve-Off Vehicle (CB Series)?
A:
You should install the flow control spring to the hydraulic pump housing assembly, install the control valve assembly, lubricate the O-ring seal with power steering fluid, install the O-ring seal onto the O-ring union fitting and install the O-ring union fitting into the hydraulic pump housing assembly.
By Bob
GM Specialist
01/11/2022See more FAQs (4)