FAQ for Seat Cushion Pad Repair
Q: How to remove the Seat Cushion Pull Strap-Rear No. 1 (TrailBlazer, Envoy, Rainier)?
A:
You should remove the rear seat cushion assembly from the vehicle, the rear-seat cushion cover and pad, and the strap from the rear seat cushion latch.
By BobGM Specialist
01/11/2022 Q: How to install the Seat Cushion Panel-Rear No. 2?
A:
You should install the seat cushion panel on the pad and cover, the J-strips securing the seat cushion cover to the seat cushion panel, the pull handle, and the rear seat cushion assembly to the seat latch rod with two rear seat cushion bolts.
By BobGM Specialist
01/11/2022 Q: How to remove the Seat Cushion Cover and Pad-Rear No. 1 (TrailBlazer, Envoy, Rainier)?
A:
You should remove the seat cushion from the vehicle, the seat cushion bracket, and the seat latch bezels, remove the push pins on the underside of the seat bottom, fold the carpet back to release the J-strips that retain the cover to the seat pan, compress the foam and partially remove the seat cover assembly from the seat pan, remove the cover from the cushion by separating the retaining strips, separate and remove the cushion and cover assembly from the seat pan, release the reinforcement bar from the hog-rings and remove the cover from the cushion.
By BobGM Specialist
01/11/2022 Q: How to install the Seat Cushion Outer Trim Panel?
A:
You should install the trim panel to the power seat and the trim panel to the manual seat.
By BobGM Specialist
01/11/2022 Q: What is the recommended torque for the trim panel screws?
A:
The recommended torque is 3 Nm (26 lb in).
By BobGM Specialist
01/11/2022 Q: How to remove the Seat Cushion Frame - Front?
A:
You should remove the 3 seat switch bezel mounting screws, the 4 nuts that secure the seat pan to the power seat adjuster frame, and the clip from the front outboard seat pan stud, disconnect the black electrical connector, the black electrical connector, and the gray lumbar electrical connector, remove the supplemental inflatable restraint (SIR)harness from the harness clips, the SIR harness from the seat, the seat harness from the seat pan, the seat memory module, the seat cushion assembly, the seat cushion cover and pad from the seat frame and the wiring harness and connector clips if you are replacing the frame.
By BobGM Specialist
01/11/2022 Q: How to remove the Seat Cushion Bracket-Rear No. 1?
A:
You should remove the rear seat cushion assembly from the vehicle, the 2 bolts securing the bracket assembly to the seat cushion, and the bracket assembly from the seat cushion.
By BobGM Specialist
01/11/2022 Q: How to remove the Seat Cushion Outer Trim Panel?
A:
You should remove the trim panel from the power seat, the trim panel from the manual seat, and the trim panel from the seat assembly.
By BobGM Specialist
01/11/2022 Q: How to remove the Seat Cushion Pull Strap-Rear No. 1?
A:
You should remove the rear seat cushion assembly from the vehicle, the rear-seat cushion cover and pad, and the strap from the rear seat cushion latch.
By BobGM Specialist
01/11/2022 Q: How to install the Seat Cushion Pull Strap-Rear No. 1 (TrailBlazer, Envoy, Rainier)?
A:
You should install the small loop onto the rear seat cushion latch, the strap through the opening in the seat pan, the rear-seat cushion cover and pad, and the rear seat cushion assembly to the vehicle.
By BobGM Specialist
01/11/2022 See more FAQs (22)