Search Bar
Search by Part Number, Part Name, or Vehicle
  • My Garage
  • Cart
  • OE Parts
  • Body & Mirrors
  • Chassis & Brakes
  • Engine & Drivetrain
  • Electrical & Lighting
Help Center
< Back ×
  • Shop OE Parts
  • Shop By Category
  • Body & Mirrors
  • Chassis & Brakes
  • Engine & Drivetrain
  • Electrical & Lighting

2005 Chevrolet Blazer Fuel Injector

My Vehicle Change Vehicle
2005 Chevrolet Blazer
Change Vehicle
Vehicle Options
We need more information about your vehicle to make a correct determination of fitment
< Back to View All
Fuel Systems
  • Department
  • Prices

1 Product found

4 Q&A for Fuel Injector Repair
Sort by:
Recommended
Filter Results
Sort
View by
  • OEM 2005 Chevrolet Blazer Injector Diagram - 88894353
    View Related Parts

    OEM (Genuine) 2005 Chevrolet Blazer Injector

    PartNumber: 88894353
    $129.42 MSRP: $244.20
    You Save: $114.78 (48%)
    Product Specifications
    • Notes: 4.3l Sfi; Engine Vin Code X
    • Other Names: Injector
    • Item Dimensions: 10.4 x 3.6 x 1.1 inches
    • Item Weight: 0.50 Pounds
    • Fitment Type: Direct Replacement
    • Part Description: 2005 Chevrolet Blazer Injector
    More Info
    Vehicle Fitment
    • 2005 Chevrolet Blazer | Base, LS, Xtreme, ZR2 | 6 Cyl 4.3 L GAS

FAQ for Fuel Injector Repair

Q: What is the recommended torque for the fuel pipe bolt?
A:
The recommended torque is 6 Nm (53 lb-ft).
By Bob
GM Specialist
01/11/2022
Q: What kind of special tools will be required in the Fuel Injector Cleaning?
A:
J44466-12 CSFI Fuel Metering Body Jumper Block, J 44466-13 Screws, J 44466-11 IAFM Fuel Transfer Tube Recycling Block, J 41413 EVAP Pressure and Purge Station, J 44466-10 Regulator and Hose Assembly, J 39021 Fuel Injector Coil and Balance Tester, J 39021-210 Injector Tester Adapter Box, J 39021-301 V6 Fuel Injector Test Adapter, and J 38500-A Fuel Injector Cleaner.
By Bob
GM Specialist
01/11/2022
Q: How to install the Fuel Injector?
A:
You need to lubricate the new injector O-ring seals with clean engine oil, install the fuel injector into the fuel meter body injector socket, install the retainer and the injector retainer lock nuts, then install the fuel meter body.
By Bob
GM Specialist
01/11/2022
Q: What is the recommended torque for the injector retainer lock nuts?
A:
The recommended torque is 3 Nm (27 lb in).
By Bob
GM Specialist
01/11/2022

FAQ for Other Repair Info

Q: How to remove the Fuel Level Sensor?
A:
You need to disconnect the negative battery cable, relieve the fuel system pressure, drain and remove the fuel tank, remove the fuel sender assembly, disconnect the fuel pump electrical connector, remove the Fuel Level Sensor electrical connector retaining clip, disconnect the fuel level sensor electrical connector from under the fuel sender cover, remove the fuel level sensor retaining clip, squeeze the locking tangs and remove the fuel level sensor.
Q: What is the installation procedure for the Fuel Tank Pressure Sensor (utility/crew cab)?
A:
The procedure is to install the Fuel Tank Pressure Sensor on the fuel sender assembly, connect the fuel tank pressure sensor electrical connector, install and refill the fuel tank, install the fuel filler cap, connect the negative battery cable, and inspect for leaks.
Q: How to install the Fuel Pressure Regulator?
A:
You need to lubricate the new O-rings seals with clean engine oil, assemble the new backup ring, regulator seal O-rings, and regulator filter to the Fuel Pressure Regulator, next install the fuel pressure regulator with the vacuum tube pointing down, then install the fuel pressure regulator retainer clip, and finally install the upper manifold.