Contact Us Live Chat or 1-888-220-8330
Search Bar
Search by Part Number or Keywords
  • My Garage
  • My Account
  • Cart
  • Body & Mirrors
  • Chassis & Brakes
  • Engine & Drivetrain
  • Electrical & Lighting
Help Center
< Back ×
  • Body & Mirrors
  • Chassis & Brakes
  • Engine & Drivetrain
  • Electrical & Lighting
Login/Register My Account Track Order Help Center Contact Us
Replacement and OEM Parts for 2006 Chevrolet Corvette Suspension Control Module

2006 Chevrolet Corvette Suspension Control Module

My Vehicle Change Vehicle
2006 Chevrolet Corvette
Change Vehicle
Vehicle Options
We need more information about your vehicle to make a correct determination of fitment
< Back to View All
Air Suspension
  • Department
  • Prices

1 Product found

3 Q&A for Suspension Control Module Repair
Show Item:
  • 30
  • 60
  • 90
Sort by:
Recommended
Filter
Sort
View by
  • OEM 2006 Chevrolet Corvette Module Asm-Electronic Suspension Control Diagram - 15808061
    View Related Parts

    OEM (Genuine) 2006 Chevrolet Corvette Module Asm-Electronic Suspension Control

    PartNumber: 15808061
    OEM 2006 Chevrolet Corvette Module Asm-Electronic Suspension Control - 15808061
    Product Specifications
    • Notes: Corvette
    • Other Names: Control Module, Module
    • Item Dimensions: 10.4 x 6.9 x 2.9 inches
    • Item Weight: 2.30 Pounds
    • Fitment Type: Direct Replacement
    • Replaces: 15229333, 25814227, 10367688
    • Part Description: 2006 Chevrolet Corvette Module Asm-Electronic Suspension Control
    More Info
    Vehicle Fitment
    • 2006 Chevrolet Corvette | 427 Limited Edition Z06, Base, Z06 | 8 Cyl 6.0 L GAS, 8 Cyl 6.2 L GAS, 8 Cyl 7.0 L GAS

FAQ for Suspension Control Module Repair

Q: How to physically inspect the Electronic Suspension Control?
A:
You should inspect for aftermarket devices that could affect the operation of the electronic suspension control (ESC) system, and inspect the easily accessible or visible system components for obvious damage or conditions which could cause the symptom. then inspect the connectors to be properly seated and free of corrosion.
By Bob
GM Specialist
01/11/2022
Q: What is the installation procedure for the Electronic Suspension Control Module?
A:
The procedure is to connect the ESC module connectors, install the ESC module into the mounting bracket, and secure the LR floor compartment lid.
By Bob
GM Specialist
01/11/2022
Q: How to remove the Electronic Suspension Control Module?
A:
You need to raise the LR floor compartment lid, push down the ESC module to remove it from the mounting bracket and disconnect the ESC module connectors.
By Bob
GM Specialist
01/11/2022

FAQ for Other Repair Info

Q: What is the installation procedure for the Park Brake Cable- Rear?
A:
The procedure is to install the rear Parking Brake Cable, install the rear parking brake cable retainer nut, connect the rear park brake cable to the rear suspension mounting bracket, connect the rear park brake cable to the retainer and equalizer, and install the RH muffler, then enable the park brake automatic adjuster.
Q: How to install the Steering Knuckle?
A:
You need to install the Steering Knuckle to the upper control arm and the lower control arm, install the steering linkage outer tie rod ball stud to the steering knuckle, install the stabilizer shaft link to the lower control arm, connect the wheel speed sensor electrical connector, install the brake rotor and caliper, the tire and wheel assembly. Check the front wheel toe and adjust as necessary.
Q: What is the disassembly procedure for the Master Cylinder Overhaul?
A:
The procedure is to remove the Brake Master Cylinder, secure the mounting flange of the brake master cylinder in a bench vise, clean the outside of the master cylinder reservoir on and around the reservoir cap, remove the reservoir cap and diaphragm from the reservoir, inspect the reservoir cap and diaphragm for cuts or cracks, nicks or deformation, remove the master cylinder reservoir from the master cylinder, depress the primary piston and remove the piston retainer, remove the primary piston assembly, plug the cylinder inlet ports and the rear outlet port, and discard the primary piston assembly, the piston retainer, and the seals and seal retainer from the secondary piston.