< Back ×
My Vehicle Change Vehicle
2006 Chevrolet Equinox
< Back to View All
Hoods
- Department
- Prices
OEM (Genuine) 2006 Chevrolet Equinox Plate Asm-Hood Secondary Striker & Primary Latch
PartNumber: 15799992
Product Specifications- Other Names: Lock, Lock Plate
- Item Dimensions: 9.4 x 4.0 x 3.3 inches
- Item Weight: 0.90 Pounds
- Fitment Type: Direct Replacement
- Replaces: 22692285
- Part Description: 2006 Chevrolet Equinox Plate Asm-Hood Secondary Striker & Primary Latch
Vehicle Fitment- 2006 Chevrolet Equinox | LS, LT, LTZ, Sport | 6 Cyl 3.4 L GAS, 6 Cyl 3.6 L GAS
OEM (Genuine) 2006 Chevrolet Equinox Latch Asm-Hood Secondary
PartNumber: 15799991
Product Specifications- Other Names: Lock, Safety Catch
- Item Dimensions: 5.6 x 4.5 x 2.6 inches
- Item Weight: 0.60 Pounds
- Fitment Type: Direct Replacement
- Replaces: 5481479, 05481479
- Part Description: 2006 Chevrolet Equinox Latch Asm-Hood Secondary
Vehicle Fitment- 2006 Chevrolet Equinox | LS, LT, LTZ, Sport | 6 Cyl 3.4 L GAS, 6 Cyl 3.6 L GAS
FAQ for Hood Latch Repair
Q: How to install the hood hinge?
A:
You can install the hinge to the hood bolts and lower the hood.
By Bob
GM Specialist
01/11/2022Q: What is the removal procedure for the hood latch?
A:
You can mark the hood latch location, remove the hood latch bolts and disconnect the release cable.
By Bob
GM Specialist
01/11/2022Q: How to remove the seal?
A:
You can open the hood, located at the end of the hood seal, from the fender, pull the rear side hood seal, remove the seal from the vehicle and clean the area.
By Bob
GM Specialist
01/11/2022Q: What is the removal procedure for the seal?
A:
The procedure is to open the hood, and then pull the hood rear seal from the cowl panel flange.
By Bob
GM Specialist
01/11/2022Q: How to install the hood latch?
A:
You can install the hood latch release cable and the hood latch bolts.
By Bob
GM Specialist
01/11/2022Q: What is the recommended torque for the hood bolts?
A:
The recommended torque is 25 N.M (18 lb-ft).
By Bob
GM Specialist
01/11/2022Q: How to install the seal?
A:
You can prepare the body surface by wiping with isopropyl alcohol, remove the protective backing paper from the adhesive on the rear side hood seal, install the rear side hood seal and then close the hood.
By Bob
GM Specialist
01/11/2022Q: How to remove the hood hinge?
A:
You can raise and support the hood, mark the position of the hood hinge and remove the hinge bolts and the hinge.
By Bob
GM Specialist
01/11/2022Q: What is the recommended torque for the hood bolts?
A:
The recommended torque is 10 Nm (89 lb in).
By Bob
GM Specialist
01/11/2022Q: What is the installation procedure for the seal?
A:
The procedure is to place the hood rear seal to the vehicle, push the hood rear seal onto the cowl panel flange to fully seat the seal, and then verify hood seal fits flush against the hood rear side seals.
By Bob
GM Specialist
01/11/2022See more FAQs (7)