Search Bar
Search by Part Number, Part Name, or Vehicle
  • My Garage
  • Cart
  • OE Parts
  • Body & Mirrors
  • Chassis & Brakes
  • Engine & Drivetrain
  • Electrical & Lighting
Help Center
< Back ×
  • Shop OE Parts
  • Shop By Category
  • Body & Mirrors
  • Chassis & Brakes
  • Engine & Drivetrain
  • Electrical & Lighting

2006 Chevrolet Impala Engine Control Module

My Vehicle Change Vehicle
2006 Chevrolet Impala
Change Vehicle
Vehicle Options
We need more information about your vehicle to make a correct determination of fitment
< Back to View All
Ignition, Distributors & ECM
  • Department
  • Brands
  • Prices

2 Products found

1 Q&A for Engine Control Module Repair
Sort by:
Recommended
Filter Results
Sort
View by
  • OEM 2006 Chevrolet Impala Engine Control Module (W/ 2Nd Mpu W/O Boot)& Calibration - 12596679
    OEM 2006 Chevrolet Impala Engine Control Module (W/ 2Nd Mpu W/O Boot)& Calibration Diagram - 12596679
    View Related Parts

    OEM (Genuine) 2006 Chevrolet Impala Engine Control Module (W/ 2Nd Mpu W/O Boot)& Calibration

    PartNumber: 12596679
    Product Specifications
    • Notes: 3.5 & 3.9 Liter; 5.3 Liter; Impala, Monte Carlo
    • Other Names: ECM, PCM
    • Item Dimensions: 7.8 x 5.5 x 5.4 inches
    • Item Weight: 2.00 Pounds
    • Fitment Type: Direct Replacement
    • Part Description: 2006 Chevrolet Impala Engine Control Module (W/ 2Nd Mpu W/O Boot)& Calibration
    More Info
    Vehicle Fitment
    • 2006 Chevrolet Impala | LS, LT, LTZ, Police, SS | 6 Cyl 3.5 L FLEX, 6 Cyl 3.5 L GAS, 6 Cyl 3.9 L GAS, 8 Cyl 5.3 L GAS
  • Cardone Reman Remanufactured Engine Control Computer for 2006 Chevrolet Impala - 77-6679F

    Cardone Reman® Remanufactured Engine Control Computer for 2006 Chevrolet Impala

    PartNumber: 77-6679F
    Product Specifications
    • Notes: with OE # 12596679;Vehicle specific Flash programming req'd ON or OFF the vehicle.Accurate VIN & mileage are req'd. Additional vehicle specific on-car programming must be performed AFTER installation to prevent drivability & starting issues.
    • Connector/Terminal Configuration: Pin/Male; Pin/Male; Pin/Male
    • E-Waste: Yes
    • Housing Material: Metal
    • Product Condition: Remanufactured
    • Removable PROM: No
    • Terminal Quantity: 56, 73, 56
    • Part Description: 2006 Chevrolet Impala Remanufactured Engine Control Computer
    More Info
    Vehicle Fitment
    • 2006 Chevrolet Impala | All Trims | 8 Cyl 5.3L

FAQ for Engine Control Module Repair

Q: How do I prevent any possible electrostatic discharge damage to the ECM?
A:
You should not touch the connector pins or the soldered components on the circuit board.
By Bob
GM Specialist
01/11/2022

FAQ for Other Repair Info

Q: What should be done before servicing the Ignition Lock Cylinder?
A:
Disconnect the negative battery cable, disable the SIR system, remove the tilt lever, and remove the steering wheel and the steering column trim covers. Perform passkey relearn after the Ignition Lock Cylinder has been replaced.
Q: What is the recommended torque for the ignition coil bolts?
A:
The recommended torque is 8 N.m (71 lb in).
Q: What should be done before servicing the Knock Sensor?
A:
Drain the cooling system.