< Back ×
2007 Buick Lucerne Camber and Alignment Kit
My Vehicle Change Vehicle
2007 Buick Lucerne
< Back to View All
Alignment Kits
- Department
- Prices
OEM (Genuine) 2007 Buick Lucerne U-Bolt Nut
PartNumber: 11516382$1.14 MSRP:$1.88You Save: $0.74 (40%)Product Specifications- Location: Driver Side; Passenger Side
- Item Dimensions: 4.2 x 3.0 x 0.7 inches
- Item Weight: 0.70 Pounds
- Fitment Type: Direct Replacement
- Replaces: 22123946, 15702050, 15048124, 14013439
- Part Description: 2007 Buick Lucerne U-Bolt Nut
Vehicle Fitment- 2007 Buick Lucerne | CX, CXL, CXL Special Edition, CXS, Super | 6 Cyl 3.8 L GAS, 6 Cyl 3.9 L FLEX, 6 Cyl 3.9 L GAS, 8 Cyl 4.6 L GAS
Product Specifications- Location: Driver Side; Passenger Side
- Item Dimensions: 5.5 x 1.9 x 1.6 inches
- Item Weight: 0.60 Pounds
- Fitment Type: Direct Replacement
- Replaces: 25666108, 25630801, 11518694
- Part Description: 2007 Buick Lucerne Bolt, Rear Suspension Support
Vehicle Fitment- 2007 Buick Lucerne | CX, CXL, CXL Special Edition, CXS, Super | 6 Cyl 3.8 L GAS, 6 Cyl 3.9 L FLEX, 6 Cyl 3.9 L GAS, 8 Cyl 4.6 L GAS
Product Specifications- Location: Driver Side; Passenger Side
- Item Dimensions: 5.4 x 2.4 x 2.0 inches
- Item Weight: 0.50 Pounds
- Fitment Type: Direct Replacement
- Replaces: 25671630
- Part Description: 2007 Buick Lucerne Adjust Bolt
Vehicle Fitment- 2007 Buick Lucerne | CX, CXL, CXL Special Edition, CXS, Super | 6 Cyl 3.8 L GAS, 6 Cyl 3.9 L FLEX, 6 Cyl 3.9 L GAS, 8 Cyl 4.6 L GAS
Product Specifications- Location: Driver Side; Passenger Side
- Item Dimensions: 5.1 x 1.2 x 1.2 inches
- Item Weight: 0.50 Pounds
- Fitment Type: Direct Replacement
- Part Description: 2007 Buick Lucerne Bolt/Screw-Rear Suspension Control Arm
Vehicle Fitment- 2007 Buick Lucerne | CX, CXL, CXL Special Edition, CXS, Super | 6 Cyl 3.8 L GAS, 6 Cyl 3.9 L FLEX, 6 Cyl 3.9 L GAS, 8 Cyl 4.6 L GAS
FAQ for Camber and Alignment Kit Repair
Q: What should be done before measuring the trim heights?
A:
Set the tire pressures to the pressure shown on the certification label. Check the fuel level. Add additional weight if necessary to simulate a full tank. Ensure the rear compartment is empty except for the spare tire. Ensure the vehicle is on a level surface. Close the doors. Close the hood. All dimensions are measured vertically to the ground. Trim heights should be within 13 mm (0.5 in) to be considered correct.
By Bob
GM Specialist
01/11/2022Q: What special tool will I be needing?
A:
You will be needing a camber adjustment tool.
By Bob
GM Specialist
01/11/2022Q: How do you measure the front and rear alignment angles?
A:
Install the alignment equipment according to the manufacturer's instructions. Jounce the front and the rear bumpers 3 times before checking the wheel alignment. Measure the alignment angles and record the readings.
By Bob
GM Specialist
01/11/2022