< Back ×
2007 Buick Lucerne Exhaust Heat Shield
My Vehicle Change Vehicle
2007 Buick Lucerne
< Back to View All
Exhaust Manifolds, Pipes & Mufflers
- Department
- Prices
Product Specifications- Notes: 3.8 Liter; 4.6 Liter
- Other Names: Heat Shield
- Item Dimensions: 55.5 x 18.0 x 5.6 inches
- Item Weight: 2.20 Pounds
- Fitment Type: Direct Replacement
- Replaces: 25901329, 15809449
- Part Description: 2007 Buick Lucerne Insulator-Floor Panel Front Center
Vehicle Fitment- 2007 Buick Lucerne | CX, CXL, CXL Special Edition, CXS, Super | 6 Cyl 3.8 L GAS, 6 Cyl 3.9 L FLEX, 6 Cyl 3.9 L GAS, 8 Cyl 4.6 L GAS
Product Specifications- Notes: 3.8 Liter, Federal
- Location: Passenger Side
- Other Names: Heat Shield
- Item Dimensions: 20.3 x 9.3 x 3.7 inches
- Item Weight: 0.90 Pounds
- Fitment Type: Direct Replacement
- Part Description: 2007 Buick Lucerne Shield-Exhaust Manifold Heat
Vehicle Fitment- 2007 Buick Lucerne | CX, CXL | 6 Cyl 3.8 L GAS
Product Specifications- Notes: 4.6 Liter
- Item Dimensions: 3.3 x 3.2 x 2.8 inches
- Item Weight: 0.50 Pounds
- Fitment Type: Direct Replacement
- Part Description: 2007 Buick Lucerne EGR Valve Upper Bracket
Vehicle Fitment- 2007 Buick Lucerne | CXL, CXS, Super | 8 Cyl 4.6 L GAS
Product Specifications- Notes: 3.8 Liter, California;3.8 Liter, Federal
- Location: Driver Side
- Other Names: Heat Shield
- Item Dimensions: 21.6 x 7.0 x 6.1 inches
- Item Weight: 1.30 Pounds
- Fitment Type: Direct Replacement
- Part Description: 2007 Buick Lucerne Shield-Exhaust Manifold Heat
Vehicle Fitment- 2007 Buick Lucerne | CX, CXL | 6 Cyl 3.8 L GAS
Product Specifications- Notes: 3.8 Liter, California
- Location: Passenger Side
- Other Names: Heat Shield, Shield
- Item Dimensions: 17.2 x 6.1 x 5.3 inches
- Item Weight: 0.70 Pounds
- Fitment Type: Direct Replacement
- Part Description: 2007 Buick Lucerne Shield-Exhaust Manifold Heat
Vehicle Fitment- 2007 Buick Lucerne | CX, CXL | 6 Cyl 3.8 L GAS
Product Specifications- Notes: 3.8 Liter
- Other Names: Heat Shield
- Item Dimensions: 6.3 x 5.2 x 4.1 inches
- Item Weight: 0.80 Pounds
- Fitment Type: Direct Replacement
- Part Description: 2007 Buick Lucerne Bracket-Engine Wiring Harness Shield
Vehicle Fitment- 2007 Buick Lucerne | CX, CXL | 6 Cyl 3.8 L GAS
FAQ for Exhaust Heat Shield Repair
Q: What is the removal procedure for the Oxygen Sensor Wiring Harness Heat Shield?
A:
Raise and support the vehicle. Refer to Vehicle Lifting. Drill out the rivets. Lower the heat shield until the heated oxygen sensor clips can be disconnected. Disconnect the HO2S clips from the heat shield. Remove the heat shield.
By Bob
GM Specialist
01/11/2022Q: What is the installation procedure for the Oxygen Sensor Wiring Harness Heat Shield?
A:
Raise the heat shield until the HO2S clips can be connected. Connect the HO2S clips to the heat shield. Position the heat shield on the floor panel. Using a rivet gun, install the rivets. Lower the vehicle.
By Bob
GM Specialist
01/11/2022