Search Bar
Search by Part Number, Part Name, or Vehicle
  • My Garage
  • Cart
  • OE Parts
  • Body & Mirrors
  • Chassis & Brakes
  • Engine & Drivetrain
  • Electrical & Lighting
Help Center
< Back ×

2007 Buick Lucerne Seat Heater Pad

My Vehicle Change Vehicle
2007 Buick Lucerne
Change Vehicle
Vehicle Options
We need more information about your vehicle to make a correct determination of fitment
< Back to View All
Power & Heated Seat
  • Department
  • Prices

1 Product found

13 Q&A for Seat Heater Pad Repair
Sort by:
Recommended
Filter Results
Sort
View by
  • OEM 2007 Buick Lucerne Heater Asm-Driver Seat Back Cushion - 15268884
    Product Specifications
    • Notes: Passenger Seat, Seat Back; Driver Seat, Seat Back
    • Other Names: Seat Back Heater
    • Item Dimensions: 13.3 x 4.4 x 4.3 inches
    • Item Weight: 0.60 Pounds
    • Fitment Type: Direct Replacement
    • Part Description: 2007 Buick Lucerne Heater Asm-Driver Seat Back Cushion
    More Info
    Vehicle Fitment
    • 2007 Buick Lucerne | CX, CXL, CXL Special Edition, CXS, Super | 6 Cyl 3.8 L GAS, 6 Cyl 3.9 L FLEX, 6 Cyl 3.9 L GAS, 8 Cyl 4.6 L GAS

FAQ for Seat Heater Pad Repair

Q: How do you remove the Seat Cushion Heater Element?
A:
The heater assembly is attached to the seat cushion with adhesive, carefully pull away from the cushion to remove it.
By Bob
GM Specialist
01/11/2022
Q: How do you test the Circuit System?
A:
Ignition OFF, disconnect the harness connector at the appropriate seat cushion or seat back ventilation heat and cool module. Connect a test lamp between the control circuit terminal 7 and the ground.
By Bob
GM Specialist
01/11/2022
Q: How do you remove the Front Seat Back Heater?
A:
The heater assembly is attached to the seat back cushion with adhesive, carefully pull it away from the seat to remove it.
By Bob
GM Specialist
01/11/2022
Q: How do you reset the CCS module?
A:
Cycled OFF then ON the ignition between each test to reset the CCS module.
By Bob
GM Specialist
01/11/2022
Q: What should be done if the Heated and Cooled Seat Switch Indicators are always On?
A:
Ignition OFF, and disconnect the harness connector at the heated and cooled seat switch. Ignition ON, heated and cool seat OFF. Test for less than 0 volts between the illuminated indicator control circuit and the ground. If greater than 0 volts, test the control circuit for a short voltage. If the circuit tests normal, replace the door module.
By Bob
GM Specialist
01/11/2022
Q: What the scan tool will do When the heated seat is on?
A:
When the heated seat is on, the scan tool will display the status of the seat back heating element as Active.
By Bob
GM Specialist
01/11/2022
Q: What should you do before using the symptom tables?
A:
Perform the Diagnostic System Check-Vehicle to verify that there are no DTCs set and that the control modules can communicate via the serial data link.
By Bob
GM Specialist
01/11/2022
Q: What can I do with the passenger heated seat inoperative if all circuits test normal?
A:
Test or replace the heated seat switch.
By Bob
GM Specialist
01/11/2022
Q: How many screws attach to the Front Seat Cushion Blower Assembly?
A:
9screws attach to the Front Seat Cushion Blower Assembly.
By Bob
GM Specialist
01/11/2022
Q: What should be done before servicing the Duct?
A:
Remove the front seat back cushion rear finish panel.
By Bob
GM Specialist
01/11/2022
See more FAQs (8)