< Back ×
My Vehicle Change Vehicle
2007 Buick Rainier
< Back to View All
Steering Racks & Gearboxes
- Department
- Prices
OEM (Genuine) 2007 Buick Rainier Gear Kit, Steering (Remanufacture)
PartNumber: 19330461
Product Specifications- Other Names: Gear Assembly, Steering Gear
- Item Dimensions: 51.8 x 11.2 x 6.1 inches
- Item Weight: 15.20 Pounds
- Fitment Type: Direct Replacement
- Replaces: 19207782, 19150430
- Part Description: 2007 Buick Rainier Gear Kit, Steering (Remanufacture)
Vehicle Fitment- 2007 Buick Rainier | CXL | 6 Cyl 4.2 L GAS, 8 Cyl 5.3 L GAS
OEM (Genuine) 2007 Buick Rainier Gear Kit, Steering (Remanufacture)
PartNumber: 19330462Product Specifications- Notes: Rainier
- Other Names: Gear Assembly, Steering Gear
- Item Dimensions: 6.4 x 51.0 x 11.3 inches
- Item Weight: 15.20 Pounds
- Fitment Type: Direct Replacement
- Replaces: 19207780, 88965356, 26101416
- Part Description: 2007 Buick Rainier Gear Kit, Steering (Remanufacture)
Vehicle Fitment- 2007 Buick Rainier | CXL, CXL Plus | 6 Cyl 4.2 L GAS, 8 Cyl 5.3 L GAS
FAQ for Steering Gearbox Repair
Q: How to assemble the Steering Gear Inner Tie Rod-Off Vehicle (Quiet Valve)?
A:
You should attach the inner tie rod onto the rack, place a pipe wrench on the rack next to the inner tie rod housing, place a torque wrench and J 34028 on the flats of the inner tie rod housing, attach the inner tie rod onto the rack, place a pipe wrench on the rack next to the inner tie rod housing, place a torque wrench and J 34028 on the flats of the inner tie rod housing, and assemble the rack and pinion boot.
By Bob
GM Specialist
01/11/2022Q: What is the recommended torque for the adjuster plug stationary while tightening the adjuster plug lock nut?
A:
The recommended torque is 68 N.m (50 lb-ft).
By Bob
GM Specialist
01/11/2022Q: How to install the Power Steering Gear?
A:
You should install the outer tie rods, the power steering gear to the vehicle, and the power steering gear mounting bolts, remove the support from the power steering gear, install the power steering hose assembly to the power steering gear, the power steering hose assembly to the power steering gear retaining bolt, the steering gear crossmember, the outer tie rods to steering knuckles retaining nuts, and the tires and wheels, and remove the drain pan from under the vehicle.
By Bob
GM Specialist
01/11/2022Q: How to install the Steering Gear Cylinder Pipe Assembly and Seals-Off Vehicle?
A:
You should install the TORX(R) screw into the cylinder line retaining plate, tighten using an E 8 socket, and tighten both cylinder line nuts at the cylinder end.
By Bob
GM Specialist
01/11/2022Q: How to remove the Power Steering Gear?
A:
You should install a drain pan under the vehicle, the tires and wheels, the outer tie rods retaining nuts and discard the nuts, the steering gear crossmember, the power steering hose assembly to the power steering gear retaining bolt, the power steering hose assembly from the power steering gear, the power steering gear mounting bolts, the power steering gear from the vehicle, the outer tie rods from the inner tie rods.
By Bob
GM Specialist
01/11/2022Q: How to assemble the Steering Gear Inner Tie Rod-Off Vehicle (Magnasteer)?
A:
You should attach the inner tie rod onto the rack, place a pipe wrench on the rack next to the inner tie rod housing, place a torque wrench and J 34028 on the flats of the inner tie rod housing, attach the inner tie rod onto the rack, place a pipe wrench on the rack next to the inner tie rod housing, place a torque wrench and J 34028 on the flats of the inner tie rod housing, place the inner tie rod assembly in a vise, insert a 0.25 mm gage between the rack and the inner tie rod housing to check both stakes, and assemble the rack and pinion boot.
By Bob
GM Specialist
01/11/2022Q: How to remove the Steering Gear Cylinder Pipe Assembly and Seals-Off Vehicle?
A:
You should remove the TORX(R) screw from the cylinder line retaining plate at the valve end, the cylinder line retaining plate, both cylinder line assemblies from the rack and pinion gear assembly, and the O-rings seals from the valve end.
By Bob
GM Specialist
01/11/2022Q: How to disassemble the Steering Gear Inner Tie Rod-Off Vehicle (Magnasteer)?
A:
You should remove the rack and pinion boot, place the gear in a vise, remove the shock dampener from the inner tie rod housing, place a pipe wrench on the rack next to the inner tie rod housing, place a wrench on the flats of the inner tie rod housing, rotate the inner tie rod housing counterclockwise, remove the shock dampener from the inner tie rod housing, place a pipe wrench on the rack, place a wrench on the flats of the inner tie rod housing, and rotate the inner tie rod housing counterclockwise.
By Bob
GM Specialist
01/11/2022Q: How to adjust the Steering Gear Rack Bearing Preload-Off Vehicle (Rack and Pinion)?
A:
You should loosen the adjuster plug lock nut, turn the adjuster plug clockwise until the adjuster plug bottoms in the gear assembly, turn the adjuster plug back 50 degrees to 70 degrees (approximately one flat) and install the adjuster plug lock nut to the adjuster plug.
By Bob
GM Specialist
01/11/2022Q: How to install the Steering Gear Boot-Off Vehicle?
A:
You should apply the grease provided to the inside of the rack and pinion boot ribs, place the new large seal retaining clamp onto the rack and pinion boot, and install the boot over the inner tie rod end, the new small seal retaining clamp over the boot, the rack and pinion gear and the outer tie rod.
By Bob
GM Specialist
01/11/2022See more FAQs (9)