Contact Us Live Chat or 1-888-220-8330
Search Bar
Search by Part Number or Keywords
  • My Garage
  • My Account
  • Cart
  • Body & Mirrors
  • Chassis & Brakes
  • Engine & Drivetrain
  • Electrical & Lighting
Help Center
< Back ×
  • Body & Mirrors
  • Chassis & Brakes
  • Engine & Drivetrain
  • Electrical & Lighting
Login/Register My Account Track Order Help Center Contact Us
Replacement and OEM Parts for 2007 Buick Rendezvous Engine Control Module

2007 Buick Rendezvous Engine Control Module

My Vehicle Change Vehicle
2007 Buick Rendezvous
Change Vehicle
Vehicle Options
We need more information about your vehicle to make a correct determination of fitment
< Back to View All
Ignition, Distributors & ECM
  • Department
  • Prices

1 Product found

3 Q&A for Engine Control Module Repair
Show Item:
  • 30
  • 60
  • 90
Sort by:
Recommended
Filter
Sort
View by
  • OEM 2007 Buick Rendezvous PCM Diagram - 19210070
    View Related Parts

    OEM (Genuine) 2007 Buick Rendezvous PCM

    PartNumber: 19210070
    OEM 2007 Buick Rendezvous PCM - 19210070
    Product Specifications
    • Notes: 3.5 Liter
    • Other Names: ECM, PCM
    • Item Dimensions: 8.2 x 7.3 x 4.1 inches
    • Item Weight: 2.20 Pounds
    • Fitment Type: Direct Replacement
    • Part Description: 2007 Buick Rendezvous PCM
    More Info
    Vehicle Fitment
    • 2007 Buick Rendezvous | CX, CXL | 6 Cyl 3.5 L GAS
    $306.27 MSRP: $576.50
    You Save: $270.23 (47%)

FAQ for Engine Control Module Repair

Q: How to remove the powertrain control module?
A:
After retrieving the percentage of remaining engine oil, you can disconnect the negative battery cable. Then you need to remove the left diagonal brace and the air cleaner assembly cover. After lifting the powertrain control module (PCM), you can disconnect the engine harness electrical connectors and remove the PCM.
By Bob
GM Specialist
01/11/2022
Q: How to install the powertrain control module?
A:
You need to install the engine harness electrical connectors, the PCM, the air cleaner assembly cove, and the air cleaner assembly cover screws. After tightening the screws, you can install the left diagonal brace and connect the negative battery cable.
By Bob
GM Specialist
01/11/2022
Q: Do we need to record the remaining engine oil life?
A:
Yes, it is necessary to record the remaining engine oil life.
By Bob
GM Specialist
01/11/2022

FAQ for Other Repair Info

Q: How to install the ignition coil?
A:
After installing the Ignition Coil studs, the ignition coil, and the ignition coil bolts/nuts, you can install the HO2S clip and the engine harness clip. Then you can connect the spark plug wires, the spark plug wires, the engine harness electrical connector, and the brake booster vacuum hose. Then you can install the intake manifold cover.
Q: How to remove the ignition lock cylinder?
A:
After disconnecting the battery negative cable and removing the steering wheel, you need to remove the retaining screw, tilt the trim cover down and slide rearward, and remove the retaining screws. Then you can lift the trim cover, insert the Snap-On A173A bent-tip awl into the access hole of the Ignition Lock Cylinder, turn the ignition lock cylinder to start, and push down on the ignition lock cylinder retainer. After that, you can release the ignition lock cylinder to the run position and remove the ignition lock cylinder from the lock cylinder case.
Q: How to install the knock sensor?
A:
After installing the Knock Sensor, you can connect the engine harness electrical connector and lower the vehicle.