Search Bar
Search by Part Number, Part Name, or Vehicle
  • My Garage
  • Cart
  • OE Parts
  • Body & Mirrors
  • Chassis & Brakes
  • Engine & Drivetrain
  • Electrical & Lighting
Help Center
< Back ×
  • Shop OE Parts
  • Shop By Category
  • Body & Mirrors
  • Chassis & Brakes
  • Engine & Drivetrain
  • Electrical & Lighting

2007 Cadillac Escalade ESV Oil Level Sensors

My Vehicle Change Vehicle
2007 Cadillac Escalade ESV
Change Vehicle
Vehicle Options
We need more information about your vehicle to make a correct determination of fitment
< Back to View All
Engine Sensors, Switches & Relays
  • Department
  • Prices

1 Product found

2 Q&A for Oil Level Sensors Repair
Sort by:
Recommended
Filter Results
Sort
View by
  • OEM 2007 Cadillac Escalade ESV Oil Level Sensor - 12603782
    OEM 2007 Cadillac Escalade ESV Oil Level Sensor Diagram - 12603782
    View Related Parts

    OEM (Genuine) 2007 Cadillac Escalade ESV Oil Level Sensor

    PartNumber: 12603782
    $28.31 MSRP: $46.88
    You Save: $18.57 (40%)
    Product Specifications
    • Item Dimensions: 5.3 x 2.2 x 2.2 inches
    • Item Weight: 0.40 Pounds
    • Fitment Type: Direct Replacement
    • Replaces: 24507190, 12579985, 12579983
    • Part Description: Oil Level Sensor
    More Info

FAQ for Oil Level Sensors Repair

Q: How do you remove the engine oil level sensor and/or switch?
A:
You need to place a suitable drain pan under the oil pan drain plug, remove the oil pan drain plug, allow the oil pan to drain completely, re-install the oil pan drain plug until snug, remove the drain pan from under the vehicle, disconnect the engine harness electrical connector from the oil level sensor and remove the oil level sensor from the oil pan.
By Bob
GM Specialist
02/11/2022
Q: How do you install the engine oil level sensor and/or switch?
A:
You need to install the oil level sensor to the oil pan, connect the engine harness electrical connector to the oil level sensor, ensure that the oil pan drain plug is tight, lower the vehicle, fill the engine with new engine oil and start the engine and inspect for leaks.
By Bob
GM Specialist
02/11/2022

FAQ for Other Repair Info

Q: How do you install the engine oil pressure sensor and/or switch?
A:
You need to apply a sealant to the threads of the new Oil Pressure Sensor. If equipped with active fuel management perform the following step, using J 41712 or equivalent, and install the oil pressure sensor and washer. If not equipped with active fuel management, perform the following step, using J 41712 or equivalent. Install the oil pressure sensor and washer, connect the engine harness electrical connector to the oil pressure sensor and install the intake manifold.
Q: What is the proper way to install the accelerator pedal position sensor?
A:
The proper way is to position the accelerator pedal to the accelerator pedal bracket and connect the APP sensor electrical connector and a scan tool to the diagnostic port to test for proper throttle-opening and throttle-closing range. Then operate the accelerator pedal and monitor the throttle angles. The accelerator pedal should operate freely, without binding, between a closed throttle, and a wide open throttle (WOT) and install the knee bolster.
Q: What is the proper way to install the camshaft position sensor (with RPO codes LY6/L76/L92)?
A:
The proper way is to Inspect the CMP O-ring seal for cuts or damage. If the seal is not cut or damaged, it may be used again. Then you can lubricate the O-ring seal with clean engine oil and install the O-ring seal onto the sensor, the CMP sensor to the front cover, and the CMP sensor wire harness. Next, you can connect the CMP sensor wire harness electrical connectors to the CMP sensor and the CMP actuator magnet, install the 3 CMP sensor wire harness bolts and connect the engine wiring harness electrical connector to the CMP sensor wire harness.