< Back ×
2007 Cadillac XLR Driveshaft
My Vehicle Change Vehicle
2007 Cadillac XLR
< Back to View All
Driveline, Axles & 4WD
- Department
- Prices
OEM (Genuine) 2007 Cadillac XLR Axle Assembly
PartNumber: 25941372$436.37 MSRP:$722.24You Save: $285.87 (40%)Product Specifications- Notes: Xlr-V, 1st Design; Xlr; 4.4l
- Location: Driver Side; Passenger Side
- Other Names: Axle Assembly
- Item Dimensions: 33.9 x 6.2 x 6.2 inches
- Item Weight: 23.30 Pounds
- Fitment Type: Direct Replacement
- Replaces: 15874726, 15891870
- Part Description: 2007 Cadillac XLR Axle Assembly
Vehicle Fitment- 2007 Cadillac XLR | V | 8 Cyl 4.4 L GAS
Product Specifications- Notes: Xlr;Xlr-V, 2nd Design; Xlr; 4.6l
- Location: Driver Side; Passenger Side
- Other Names: Axle Assembly
- Item Dimensions: 33.0 x 8.5 x 7.1 inches
- Item Weight: 22.10 Pounds
- Fitment Type: Direct Replacement
- Replaces: 10350598, 25941373, 22762284, 15851726
- Part Description: 2007 Cadillac XLR Axle Assembly
Vehicle Fitment- 2007 Cadillac XLR | Base, Platinum, V | 8 Cyl 4.4 L GAS, 8 Cyl 4.6 L GAS
Product Specifications- Notes: Xlr; 4.4l;Xlr; All
- Other Names: Drive Shaft
- Item Dimensions: 65.1 x 7.7 x 7.7 inches
- Item Weight: 23.30 Pounds
- Fitment Type: Direct Replacement
- Part Description: 2007 Cadillac XLR Propeller Shaft Assembly
Vehicle Fitment- 2007 Cadillac XLR | Base, Platinum, V | 8 Cyl 4.4 L GAS, 8 Cyl 4.6 L GAS
FAQ for Driveshaft Repair
Q: How do you install the drive line vibration dampener?
A:
You can position the dampener on the vehicle, install the two dampener bolts and install the exhaust pipe lower hanger bolts.
By Bob
GM Specialist
29/10/2022Q: What is the removal procedure for the drive line vibration dampener?
A:
The procedure is to remove the exhaust pipe lower hanger bolts, remove the two dampener bolts and remove the dampener.
By Bob
GM Specialist
29/10/2022Q: What causes a rotating squeak noise?
A:
The propeller shaft balance weight off the propeller shaft in the bottom of the driveline tube causes a rotating squeak noise.
By Bob
GM Specialist
29/10/2022Q: When does a knocking or clunking noise occur?
A:
Knocking or clunking noise occurs when operating the vehicle in high gear or coasting in NEUTRAL at 16 km/h (10 mph).
By Bob
GM Specialist
29/10/2022Q: What is the purpose of texting the vehicle under the same conditions that the customer reported?
A:
The purpose is to verify the system is operating properly.
By Bob
GM Specialist
29/10/2022Q: What may cause a whirring or squealing type of noise?
A:
Awhirring or squealing type of noise may be caused by a worn bearing.
By Bob
GM Specialist
29/10/2022Q: What causes a propeller shaft out-of-balance condition?
A:
Apropeller shaft out-of-balance condition may be caused by a bent propeller shaft, loose or missing components or weights, and worn or broken coupling.
By Bob
GM Specialist
29/10/2022Q: What may cause a sliding, scraping, or ticking type of noise during acceleration or deceleration?
A:
Adetached balance weight may cause a sliding, scraping, or ticking-type noise during acceleration or deceleration.
By Bob
GM Specialist
29/10/2022Q: What may be the cause of a rattle-type noise, mainly at idle, in the flywheel area of the transmission housing?
A:
Aloose propeller shaft hub clamp bolt may cause a rattle-type noise.
By Bob
GM Specialist
29/10/2022Q: What may create a vibration?
A:
Apropeller shaft out-of-balance condition may create a vibration.
By Bob
GM Specialist
29/10/2022See more FAQs (5)