Contact Us Live Chat or 1-888-220-8330
Search Bar
Search by Part Number or Keywords
  • My Garage
  • My Account
  • Cart
  • Body & Mirrors
  • Chassis & Brakes
  • Engine & Drivetrain
  • Electrical & Lighting
Help Center
< Back ×
  • Body & Mirrors
  • Chassis & Brakes
  • Engine & Drivetrain
  • Electrical & Lighting
Login/Register My Account Track Order Help Center Contact Us
Replacement and OEM Parts for 2007 Chevrolet Colorado Ignition Lock Cylinder

2007 Chevrolet Colorado Ignition Lock Cylinder

My Vehicle Change Vehicle
2007 Chevrolet Colorado
Change Vehicle
Vehicle Options
We need more information about your vehicle to make a correct determination of fitment
< Back to View All
Ignition, Distributors & ECM
  • Department
  • Prices

1 Product found

6 Q&A for Ignition Lock Cylinder Repair
Show Item:
  • 30
  • 60
  • 90
Sort by:
Recommended
Filter
Sort
View by
  • OEM 2007 Chevrolet Colorado Cylinder & Keys Diagram - 89022365
    View Related Parts

    OEM (Genuine) 2007 Chevrolet Colorado Cylinder & Keys

    PartNumber: 89022365
    OEM 2007 Chevrolet Colorado Cylinder & Keys - 89022365
    Product Specifications
    • Notes: W/Tilt
    • Other Names: Cylinder & Keys, Ignition Lock Cylinder
    • Item Dimensions: 5.8 x 4.6 x 1.7 inches
    • Item Weight: 0.60 Pounds
    • Fitment Type: Direct Replacement
    • Part Description: 2007 Chevrolet Colorado Cylinder & Keys
    More Info
    Vehicle Fitment
    • 2007 Chevrolet Colorado | Base, LS, LT, Sport, Sport LS, WT, Z71, Z71 LS, Z85, Z85 LS | 4 Cyl 2.8 L GAS, 4 Cyl 2.9 L GAS, 5 Cyl 3.5 L GAS, 5 Cyl 3.7 L GAS, 8 Cyl 5.3 L GAS
    $29.13 MSRP: $48.23
    You Save: $19.10 (40%)

FAQ for Ignition Lock Cylinder Repair

Q: What kind of special tools will be required in the Assembling and Coding Ignition Lock Cylinders?
A:
The tools required include J41340 Ignition Lock Holding Fixture.
By Bob
GM Specialist
01/11/2022
Q: How to install the Ignition Lock Cylinder?
A:
First, you should turn the ignition lock cylinder to the accessory (ACC) position, then push the lock cylinder in until the pin locks in the lock module, next install the steering column trim covers.
By Bob
GM Specialist
01/11/2022
Q: How to remove the Ignition Lock Cylinder?
A:
You need to remove the steering column trim covers, next turn the ignition lock cylinder to the accessory (ACC) position, then insert the 90 degrees tip of a pick-type tool into the access hole of the ignition lock cylinder, push down and hold the retaining pin of the ignition lock cylinder, finally remove the ignition lock cylinder.
By Bob
GM Specialist
01/11/2022
Q: How to inspect for proper tumbler installation?
A:
You need to hold the spring retainer in position, then insert the key into the cylinder, and the sidebar should drop down flush with the cylinder diameter if installed, finally disassemble and assemble properly as needed.
By Bob
GM Specialist
01/11/2022
Q: How to remove the Ignition Lock Cylinder Case?
A:
You need to disable the SIR system, remove the lock cylinder, the switch mounting plate, and the shear bolt from the ignition switch and lock housing assembly using a hammer and chisel, then remove the ignition switch and lock housing assembly.
By Bob
GM Specialist
01/11/2022
Q: How to install the Ignition Lock Cylinder Case?
A:
You should install the ignition switch and lock housing assembly, install the shear bolt into the ignition switch and lock housing assembly, install the switch mounting plate and the lock cylinder, then reprogram the theft deterrent system, and enable the SIR system.
By Bob
GM Specialist
01/11/2022
See more FAQs (1)

FAQ for Other Repair Info

Q: How to remove the Ignition Coil?
A:
You need to remove the air cleaner resonator and outlet duct, disconnect the engine wiring harness electrical connector from the oil pressure sensor, disconnect the engine wiring harness retainer from the oil filter adapter, disconnect the engine wiring harness retainers from the power steering pump, disconnect the engine wiring harness electrical connectors from the camshaft position (CMP) sensor, and the CMP actuator solenoid valve, then disconnect the engine wiring harness retainer from the camshaft cover, disconnect the engine wiring harness electrical connectors from the fuel injector harness, the heated oxygen sensor (HO2S), and from the engine coolant temperature (ECT) sensor, then disconnect the engine wiring harness electrical connectors from the Ignition Coils, disengage the engine wiring harness conduit from the camshaft cover, and position aside, then remove the ignition coil bolts and the ignition coils from the camshaft cover.
Q: How to remove the Knock Sensor?
A:
You need to raise and support the vehicle only high enough to access the Knock Sensor (KS) through the wheelhouse, then remove the left wheelhouse liner, disconnect the engine wiring harness electrical connector from the KS, remove the KS retaining bolt, and the KS from the engine block.
Q: How to install the Powertrain Control Module (PCM)?
A:
You should install the PCM into the PCM mounting bracket, allowing the tabs to fully engage, then connect the PCM harness connectors to the PCM body. And if a new PCM is being installed, the PCM must be programmed.