< Back ×
2007 Chevrolet Equinox Brake Master Cylinder
My Vehicle Change Vehicle
2007 Chevrolet Equinox
< Back to View All
Brake Boosters & Brake Master Cylinders
- Department
- Series
- Brands
- Prices
OEM (Genuine) 2007 Chevrolet Equinox Master Cylinder
PartNumber: 19151463$124.95 MSRP:$235.77You Save: $110.82 (48%)Product Specifications- Other Names: Master Cylinder
- Item Dimensions: 8.6 x 4.7 x 2.9 inches
- Item Weight: 1.50 Pounds
- Fitment Type: Direct Replacement
- Part Description: 2007 Chevrolet Equinox Master Cylinder
Vehicle Fitment- 2007 Chevrolet Equinox | LS, LT, LTZ, Sport | 4 Cyl 2.4 L GAS, 6 Cyl 3.0 L GAS, 6 Cyl 3.4 L GAS, 6 Cyl 3.6 L GAS
Product Specifications- UPC: 805890393849
- Part Description: 2007 Chevrolet Equinox Premium Brake Master Cylinder
Vehicle Fitment- 2007 Chevrolet Equinox | All Trims | All Engines
Product Specifications- Notes: Supplied w/o Reservoir
- Bore Diameter (N): 1.00"
- Bore Diameter (N-1): 1.415
- E-Waste: No
- Installation Hardware Included: No
- Master Cylinder Color/Finish: Gray
- Master Cylinder Material: Aluminum
- Mounting Hole Quantity: 2
- Package Contents: Master Cylinder
- Port Quantity: 2
- Primary Port Size: M12 x 1.0
- Product Condition: Remanufactured
- Reservoir Included: No
- Secondary Port Size: M12 x 1.0
- UPC: 082617787802
- Part Description: 2007 Chevrolet Equinox Remanufactured Master Cylinder
Vehicle Fitment- 2007 Chevrolet Equinox | All Trims | All Engines
FAQ for Brake Master Cylinder Repair
Q: What should you do to get access to the rear of the primary piston?
A:
You can secure the mounting flange of the brake master cylinder in a bench vise so that the rear of the primary piston is accessible.
By Bob
GM Specialist
01/11/2022Q: What should be done if the brake fluid is to be added to the master cylinder auxiliary reservoir?
A:
You will need to clean the outside of the reservoir on and around the reservoir cap before removing the cap and diaphragm.
By Bob
GM Specialist
01/11/2022Q: What's the recommended torque for the master cylinder mounting nuts?
A:
The recommended torque is 25 N.m (18 lb-ft).
By Bob
GM Specialist
01/11/2022Q: How to remove the Master Cylinder Reservoir?
A:
You will need to remove the underhood electrical center, remove the brake fluid from the reservoir and discard the fluid into an approved container, then disconnect the brake fluid level sensor electrical connector, remove the brake fluid level sensor, remove the master cylinder reservoir attachment pins and discard the pins, release the reservoir from the master cylinder by carefully pulling reservoir straight up, release the reservoir from the master cylinder by carefully pulling reservoir straight up, and then remove the reservoir seals from the master cylinder body.
By Bob
GM Specialist
01/11/2022Q: What's the recommended torque for the brake pipe fittings at the master cylinder?
A:
The recommended torque is 18 N.m (13 lb-ft).
By Bob
GM Specialist
01/11/2022Q: What's the aim of installing a rubber cap or plug to the exposed brake pipe fitting ends?
A:
It is to prevent brake fluid loss and contamination.
By Bob
GM Specialist
01/11/2022Q: What does that mean if the brake fluid level is at or below the half-full point during routine fluid checks, and an inspection of the brake system did not reveal wear or brake fluid leaks?
A:
The brake fluid may be topped off up to the maximum-fill level.
By Bob
GM Specialist
01/11/2022Q: What should be noticed when adding fluid to the brake master cylinder reservoir?
A:
You will need to use only GM-approved or equivalent DOT-3 brake fluid from a clean, sealed brake fluid container. The use of any type of fluid other than the recommended type of brake fluid may cause contamination which could result in damage to the internal rubber seals and/or rubber linings of hydraulic brake system components.
By Bob
GM Specialist
01/11/2022Q: What should be done if the brake fluid level is at or below the half-full point during routine fluid checks?
A:
You will need to inspect the brake system for wear and possible brake fluid leaks.
By Bob
GM Specialist
01/11/2022See more FAQs (4)