< Back ×
My Vehicle Change Vehicle
2007 Chevrolet Equinox
< Back to View All
Ignition, Distributors & ECM
- Department
- Prices
OEM (Genuine) 2007 Chevrolet Equinox PCM
PartNumber: 19210738
Product Specifications- Notes: 3.4 Liter; Equinox, Torrent; 3.4L
- Other Names: ECM, PCM
- Item Dimensions: 8.6 x 7.4 x 4.5 inches
- Item Weight: 2.50 Pounds
- Fitment Type: Direct Replacement
- Part Description: 2007 Chevrolet Equinox PCM
Vehicle Fitment- 2007 Chevrolet Equinox | LS, LT | 6 Cyl 3.4 L GAS
$236.27 MSRP:$444.42You Save: $208.15 (47%)
OEM (Genuine) 2007 Chevrolet Equinox Antitheft Module
PartNumber: 22756010
Product Specifications- Notes: 3.4 Liter, 2007-09
- Item Dimensions: 4.2 x 2.7 x 2.7 inches
- Item Weight: 0.40 Pounds
- Fitment Type: Direct Replacement
- Replaces: 25964111, 25912406, 10357528
- Part Description: 2007 Chevrolet Equinox Antitheft Module
Vehicle Fitment- 2007 Chevrolet Equinox | LS, LT, LTZ, Sport | 6 Cyl 3.4 L GAS, 6 Cyl 3.6 L GAS
$94.54 MSRP:$171.14You Save: $76.60 (45%)
OEM (Genuine) 2007 Chevrolet Equinox Ignition Module
PartNumber: 12595088
Product Specifications- Notes: 3.4 Liter
- Other Names: Ignition Coil, Ignition Module
- Item Dimensions: 11.3 x 5.4 x 5.2 inches
- Item Weight: 2.80 Pounds
- Fitment Type: Direct Replacement
- Replaced by: 19432144
- Part Description: 2007 Chevrolet Equinox Ignition Module
Vehicle Fitment- 2007 Chevrolet Equinox | LS, LT, LTZ | 6 Cyl 3.4 L GAS
$95.41 MSRP:$172.68You Save: $77.27 (45%)
FAQ for Ignition Control Module Repair
Q: What's the recommended torque for the 4 bolts securing the ignition coil/control module to the ignition control module bracket?
A:
The recommended torque is 4.5 N.m (40 lb in).
By Bob
GM Specialist
01/11/2022Q: How to install the ignition coil/control module?
A:
You may need to install the ignition coil/control module to the ignition control module bracket, then install the 4 bolts securing the ignition coil/control module to the ignition control module bracket, and connect the ignition coil/control module electrical connectors as well as the spark plug wires, lastly install the injector sight shield.
By Bob
GM Specialist
01/11/2022Q: How to remove the ignition coil/control module?
A:
You will need to remove the injector sight shield, then disconnect the spark plug wires and note the position, next disconnect the ignition coil/control module electrical connectors and remove the 4 bolts securing the ignition coil/control module to the ignition control module bracket, finally remove the ignition coil/control module.
By Bob
GM Specialist
01/11/2022Q: What's the recommended torque for the nut retaining the heater outlet pipe?
A:
The recommended torque is 25 N.m (18 lb-ft).
By Bob
GM Specialist
01/11/2022Q: What's the recommended torque for the ignition control module bracket nuts and bolts?
A:
The recommended torque is 25 N.m (18 lb-ft).
By Bob
GM Specialist
01/11/2022Q: How to remove the ignition control module?
A:
You will need to remove the injector sight shield, the spark plug wire retainer, and the 4 bolts securing the ignition coil/control module to the ignition control module bracket, then position the ignition coil/control module aside out of the way, and remove the bolt from the fuel injector wire harness bracket and positive crankcase ventilation (PCV) valve fresh air tube retainer, then remove the engine wire harness retainers from the ignition control module bracket studs, remove the nut retaining the heater outlet pipe, finally remove the ignition control module bracket bolts and nuts, and the ignition control module bracket.
By Bob
GM Specialist
01/11/2022See more FAQs (1)