Contact Us Live Chat or 1-888-220-8330
Search Bar
Search by Part Number or Keywords
  • My Garage
  • My Account
  • Cart
  • Body & Mirrors
  • Chassis & Brakes
  • Engine & Drivetrain
  • Electrical & Lighting
Help Center
< Back ×
  • Body & Mirrors
  • Chassis & Brakes
  • Engine & Drivetrain
  • Electrical & Lighting
Login/Register My Account Track Order Help Center Contact Us
Replacement and OEM Parts for 2007 Chevrolet Equinox Mirror Switch

2007 Chevrolet Equinox Mirror Switch

My Vehicle Change Vehicle
2007 Chevrolet Equinox
Change Vehicle
Vehicle Options
We need more information about your vehicle to make a correct determination of fitment
< Back to View All
Power Mirror Switches & Relays
  • Department
  • Prices

1 Product found

2 Q&A for Mirror Switch Repair
Show Item:
  • 30
  • 60
  • 90
Sort by:
Recommended
Filter
Sort
View by
  • OEM 2007 Chevrolet Equinox Mirror Switch Diagram - 84545374
    View Related Parts

    OEM (Genuine) 2007 Chevrolet Equinox Mirror Switch

    PartNumber: 84545374
    OEM 2007 Chevrolet Equinox Mirror Switch - 84545374
    Product Specifications
    • Other Names: Mirror Switch, Switch
    • Fitment Type: Direct Replacement
    • Replaces: 92225703
    • Part Description: 2007 Chevrolet Equinox Mirror Switch
    More Info
    Vehicle Fitment
    • 2007 Chevrolet Equinox | LS, LT, LTZ, Sport | 6 Cyl 3.4 L GAS, 6 Cyl 3.6 L GAS
    $18.09 MSRP: $27.27
    You Save: $9.18 (34%)

FAQ for Mirror Switch Repair

Q: What's the tip for replacing the power mirror switch?
A:
You may squeeze the tabs inward from the rear of the outlet assembly and push the power mirror switch out through the front of the outlet.
By Bob
GM Specialist
01/11/2022
Q: What's the tip for replacing the instrumental panel air outlet assembly?
A:
You may carefully pry out the outlet assembly using a nylon flat-bladed tool, and disconnect the electrical connectors.
By Bob
GM Specialist
01/11/2022

FAQ for Other Repair Info

Q: How to remove the Starter Motor?
A:
You will need to disconnect the battery negative cable, then raise and suitably support the vehicle. Then you should remove the Starter motor solenoid positive terminal nut and electrical wires, the starter motor solenoid S terminal nut and electrical wire, the torque converter cover bolt, the torque converter cover, the starter motor bolts, and the starter motor.
Q: How to install the underhood electrical center or junction block?
A:
You may need to install each of the following 68-way connectors into its proper location including fuse block case, forward lamp 68-way connector, engine 68-way connector, and I/P 68-way connector. Then you can push down on each connector until it is fully secured into the fuse block, connect the I/P connectors, tighten the bolts on the top of the fuse block, and tighten the underhood accessory wiring junction block harness retaining bolts to 4 N.m (35 lb in), next reconnect the positive battery cable and EPS at the end of the fuse block with the nut and tighten it to 17 N.m (13 lb-ft), finally install the Fuse Box cover and connect the negative battery cable.
Q: How to remove the sunroof motor/actuator?
A:
You will need to remove the headliner and the sunroof window, then disconnect the Sunroof Motor harness and remove the screws securing the sunroof actuator to the sunroof module and the sunroof motor.