Search Bar
Search by Part Number, Part Name, or Vehicle
  • My Garage
  • Cart
  • OE Parts
  • Body & Mirrors
  • Chassis & Brakes
  • Engine & Drivetrain
  • Electrical & Lighting
Help Center
< Back ×
  • Shop OE Parts
  • Shop By Category
  • Body & Mirrors
  • Chassis & Brakes
  • Engine & Drivetrain
  • Electrical & Lighting

2008 Buick Enclave Knock Sensor

My Vehicle Change Vehicle
2008 Buick Enclave
Change Vehicle
Vehicle Options
We need more information about your vehicle to make a correct determination of fitment
< Back to View All
Ignition, Distributors & ECM
  • Department
  • Brands
  • Prices

3 Products found

5 Q&A for Knock Sensor Repair
Sort by:
Recommended
Filter Results
Sort
View by
  • OEM 2008 Buick Enclave Knock Sensor - 12618603
    OEM 2008 Buick Enclave Knock Sensor Diagram - 12618603
    View Related Parts

    OEM (Genuine) 2008 Buick Enclave Knock Sensor

    PartNumber: 12618603
    $36.89 MSRP: $69.61
    You Save: $32.72 (48%)
    Product Specifications
    • Notes: Enclave, Traverse
    • Other Names: Knock Sensor
    • Item Dimensions: 2.6 x 2.6 x 2.1 inches
    • Item Weight: 0.40 Pounds
    • Fitment Type: Direct Replacement
    • Replaces: 12566845
    • Part Description: 2008 Buick Enclave Knock Sensor
    More Info
    Vehicle Fitment
    • 2008 Buick Enclave | CX, CXL | 6 Cyl 3.6 L GAS
  • facet Ignition Knock Sensor for 2008 Buick Enclave - 9.3012

    facet® Ignition Knock Sensor for 2008 Buick Enclave

    PartNumber: 9.3012
    $25.63
    Product Specifications
    • Part Description: 2008 Buick Enclave Ignition Knock Sensor
    Vehicle Fitment
    • 2008 Buick Enclave | CX | All Engines
    • 2008 Buick Enclave | CXL | All Engines
  • Walker Products Ignition Knock Sensor for 2008 Buick Enclave - 242-1068

    Walker Products® Ignition Knock Sensor for 2008 Buick Enclave

    PartNumber: 242-1068
    Product Specifications
    • Connector Gender: Female
    • Connector Quantity: 1
    • Connector Shape: Rectangular
    • Length: 51.82 mm
    • Mounting Hardware Included: Yes
    • Terminal Gender: Male
    • Terminal Quantity: 2
    • Terminal Type: Blade
    • UPC: 724620108129
    • Wiring Harness Included: No
    • Part Description: 2008 Buick Enclave Ignition Knock Sensor
    More Info
    Vehicle Fitment
    • 2008 Buick Enclave | All Trims | 6 Cyl 3.6L

FAQ for Knock Sensor Repair

Q: How do you install the Knock Sensor Replacement-Bank 2?
A:
You need to position the knock sensor, tighten the knock sensor bolt, connect the engine wiring harness electrical connector to the bank 2 knock sensor, raise and support the vehicle, install a new engine oil filter, and then connect the negative battery cable.
By Bob
GM Specialist
01/11/2022
Q: How do you remove the Knock Sensor Replacement-Bank 2?
A:
You need to disconnect the negative battery cable, remove the engine oil filter, lower the vehicle, disconnect the engine wiring harness electrical connector from the bank 2 knock sensor, and then loosen the knock sensor bolt and remove the knock sensor.
By Bob
GM Specialist
01/11/2022
Q: How do you remove the Knock Sensor-Bank 1?
A:
You need to remove the exhaust manifold lower heat shield, disconnect the engine wiring harness electrical connector from the bank 1 knock sensor, and then loosen the knock sensor bolt and remove the knock sensor.
By Bob
GM Specialist
01/11/2022
Q: How do you install the Knock Sensor-Bank 1?
A:
You need to position the knock sensor and tighten the knock sensor bolt, connect the engine wiring harness electrical connector to the bank 1 knock sensor, and then install the exhaust manifold lower heat shield.
By Bob
GM Specialist
01/11/2022
Q: What do you need to pay attention to when draining the cooling system?
A:
You need to know that hot engine coolant may cause severe burns, so you need to remove the knock sensor and drain the coolant.
By Bob
GM Specialist
01/11/2022

FAQ for Other Repair Info

Q: How do you install the Ignition Coil-Bank 1?
A:
You need to install the Ignition Coil(s) and the ignition coil bolt(s), connect the engine wiring harness electrical connector(s) to the ignition coil(s), position and install the UBEC bracket, and then install the UBEC bracket bolt and nuts, the body wiring harness/engine wiring harness electrical connection clip to the UBEC bracket and the UBEC.
Q: How do you remove the Ignition Lock Cylinder?
A:
You need to disconnect the battery negative cable, remove the steering column upper trim cover and the Ignition Lock Cylinder opening trim cover, turn the ignition lock cylinder to the run position, depress the retainer through the lock housing access hole with a small Allen wrench or similar pick-type tool, and then remove the ignition lock cylinder from the lock housing.
Q: How do you install the Engine Control Module?
A:
You can position the ECM bracket and install the bolts, install the ECM onto the ECM bracket support tabs and snap the ECM into place under the retaining tab, connect the engine wiring harness upper electrical connector to the ECM, install the engine wiring harness clip to the ECM bracket tab, connect the engine wiring harness middle and lower electrical connectors to the ECM and the negative battery cable, and then reprogram the ECM.