Contact Us Live Chat or 1-888-220-8330
Search Bar
Search by Part Number or Keywords
  • My Garage
  • My Account
  • Cart
  • Body & Mirrors
  • Chassis & Brakes
  • Engine & Drivetrain
  • Electrical & Lighting
Help Center
< Back ×
  • Body & Mirrors
  • Chassis & Brakes
  • Engine & Drivetrain
  • Electrical & Lighting
Login/Register My Account Track Order Help Center Contact Us
Replacement and OEM Parts for 2008 Cadillac SRX Air Hose

2008 Cadillac SRX Air Hose

My Vehicle Change Vehicle
2008 Cadillac SRX
Change Vehicle
Vehicle Options
We need more information about your vehicle to make a correct determination of fitment
< Back to View All
Air Filters & Intake Systems
  • Department
  • Prices

1 Product found

1 Q&A for Air Hose Repair
Show Item:
  • 30
  • 60
  • 90
Sort by:
Recommended
Filter
Sort
View by
  • OEM 2008 Cadillac SRX Inlet Duct Diagram - 15812947
    View Related Parts

    OEM (Genuine) 2008 Cadillac SRX Inlet Duct

    PartNumber: 15812947
    OEM 2008 Cadillac SRX Inlet Duct - 15812947
    Product Specifications
    • Notes: 3.6 Liter, 2007-09
    • Other Names: Inlet Duct, Intake Duct
    • Item Dimensions: 8.8 x 9.0 x 20.7 inches
    • Item Weight: 1.10 Pounds
    • Fitment Type: Direct Replacement
    • Part Description: 2008 Cadillac SRX Inlet Duct
    More Info
    Vehicle Fitment
    • 2008 Cadillac SRX | Base | 6 Cyl 3.6 L GAS
    $13.06 MSRP: $18.75
    You Save: $5.69 (31%)

FAQ for Air Hose Repair

Q: How to remove the Air Tube?
A:
You should raise and support the vehicle, twist the air tube seal connection on the rear shocks, disconnect the air tube from the rear shock absorber and the exhaust system from the rear exhaust hangers, remove the automatic level control compressor with the bracket attached, disconnect the air tube from the right wheel house liner clip and remove the wheelhouse liner screw to position the liner to access the air tube, the air tube from the frame at the right wheel house liner, the fuel filler neck bolt and reposition the air tubes and the air tubes from the vehicle.
By Bob
GM Specialist
01/11/2022

FAQ for Other Repair Info

Q: How to install the Throttle Body Assembly?
A:
You should carefully clean the Throttle Body mounting surfaces of any gasket and/or seal material, install the throttle body and new gasket, the throttle body bolts, the wiring harness conduit, the throttle body electrical connector, and the air cleaner intake duct, perform the throttle learn procedure and clear all diagnostic trouble codes.
Q: How to remove the Upper Intake Manifold?
A:
You should turn the ignition off, remove the fuel injector sight shield and the air inlet duct, disconnect the brake booster vacuum hose from the Intake Manifold, the purge solenoid valve electrical connector, and the purge line, remove the wiring harness retainer, disconnect the throttle body electrical connector, remove the upper intake manifold brace stud, bolt, and brace, disconnect the positive crankcase ventilation (PCV) hose, the barometric pressure sensor electrical connector, and the intake manifold runner control solenoid electrical connector, remove the injector harness bracket bolt, the left bank ignition coil wiring harness from the bracket, the upper intake manifold bolts and the upper intake manifold with the throttle body and clean and inspect the intake manifold.
Q: How to remove the Air Cleaner Element?
A:
You should first remove the air cleaner intake duct, loosen the air cleaner cover screws and open the air cleaner cover and then remove the air cleaner element.