< Back ×
2008 Cadillac STS ABS Control Module
My Vehicle Change Vehicle
2008 Cadillac STS
< Back to View All
ABS & Parking Brake
- Department
- Prices
OEM (Genuine) 2008 Cadillac STS ABS Pump Assembly
PartNumber: 89060233$395.95 MSRP:$747.11You Save: $351.16 (48%)Product Specifications- Notes: Sts, Sts-V
- Other Names: ABS Pump Assembly, Control Valve, Modulator Valve
- Item Dimensions: 8.4 x 6.1 x 6.1 inches
- Item Weight: 6.40 Pounds
- Fitment Type: Direct Replacement
- Part Description: 2008 Cadillac STS ABS Pump Assembly
Vehicle Fitment- 2008 Cadillac STS | Base, Platinum, V | 6 Cyl 3.6 L GAS, 8 Cyl 4.4 L GAS, 8 Cyl 4.6 L GAS
OEM (Genuine) 2008 Cadillac STS ABS Control Unit
PartNumber: 88964161$678.19 MSRP:$1122.49You Save: $444.30 (40%)Product Specifications- Notes: W/Sport Suspension; Sts, Sts-V; W/O Soft Ride Suspension
- Other Names: ABS Control Unit, Control Module
- Item Dimensions: 8.4 x 6.1 x 6.2 inches
- Item Weight: 3.10 Pounds
- Fitment Type: Direct Replacement
- Part Description: 2008 Cadillac STS ABS Control Unit
Vehicle Fitment- 2008 Cadillac STS | Base, Platinum, V | 6 Cyl 3.6 L GAS, 8 Cyl 4.4 L GAS, 8 Cyl 4.6 L GAS
OEM (Genuine) 2008 Cadillac STS Electronic Brake And Traction Control Module Kit
PartNumber: 89060336Product Specifications- Notes: W/O Sport Suspension; Sts, Sts-V; W/Soft Ride Suspension
- Other Names: ABS Control Unit, Control Module
- Item Dimensions: 12.2 x 10.6 x 8.3 inches
- Item Weight: 3.10 Pounds
- Fitment Type: Direct Replacement
- Part Description: 2008 Cadillac STS Electronic Brake And Traction Control Module Kit
Vehicle Fitment- 2008 Cadillac STS | Base, Platinum, V | 6 Cyl 3.6 L GAS, 8 Cyl 4.4 L GAS, 8 Cyl 4.6 L GAS
Product Specifications- Other Names: Control Valve, Modulator, Modulator Valve
- Item Dimensions: 8.2 x 7.6 x 7.4 inches
- Item Weight: 8.00 Pounds
- Fitment Type: Direct Replacement
- Part Description: 2008 Cadillac STS Brake Pressure Modulator Valve Assembly
Vehicle Fitment- 2008 Cadillac STS | Base, Platinum, V | 6 Cyl 3.6 L GAS, 8 Cyl 4.4 L GAS, 8 Cyl 4.6 L GAS
FAQ for Abs Control Module Repair
Q: How to install the Vehicle Stabilizer Control Module?
A:
The procedure is to install the stability control module bracket and the nuts, install the stability control module to the bracket, press the stability control module into the module bracket locking tabs, connect the stability control module electrical connectors, install the left rear compartment side trim panel, program the stability control module, perform the Diagnostic System Check - Vehicle.
By Bob
GM Specialist
01/11/2022Q: How to remove the Vehicle Stabilizer Control Module?
A:
The procedure is to turn the ignition switch to the off position, remove the left rear compartment side trim panel, disconnect the stability control module electrical connectors, release the stability control module from the module bracket locking tabs, lift the stability control module from the bracket and remove the stability control module, remove the stability control module bracket nuts and remove the bracket.
By Bob
GM Specialist
01/11/2022Q: What is the recommended torque for the electronic brake control module (EBCM) screws?
A:
The recommended torque is 5 N.m (44 lb in).
By Bob
GM Specialist
01/11/2022Q: What should be noticed in the replacement procedure for Electronic Brake Control Module (With JL7)?
A:
To prevent equipment damage, you should not connect or disconnect the wiring harness connector from the EBCM with the ignition switch in the on position.
By Bob
GM Specialist
01/11/2022