< Back ×
2008 Chevrolet Impala Automatic Transmission Shift Levers
My Vehicle Change Vehicle
2008 Chevrolet Impala
< Back to View All
Transmissions Components & Shifters
- Department
- Prices
$262.68 MSRP:$396.23You Save: $133.55 (34%)Product Specifications- Notes: W/O Police
- Item Dimensions: 9.3 x 19.2 x 13.1 inches
- Item Weight: 3.00 Pounds
- Fitment Type: Direct Replacement
- Replaces: 25854855, 15874380, 15921612, 20896522
- Part Description: 2008 Chevrolet Impala Gear Shift Assembly
Vehicle Fitment- 2008 Chevrolet Impala | 50th Anniversary Edition, LS, LT, LTZ, SS | 6 Cyl 3.5 L FLEX, 6 Cyl 3.5 L GAS, 6 Cyl 3.9 L FLEX, 6 Cyl 3.9 L GAS, 8 Cyl 5.3 L GAS
$40.92 MSRP:$64.36You Save: $23.44 (37%)Product Specifications- Notes: Column Shift; Floor Shift
- Other Names: Lever, Release Lever, Tilt Bracket, Tilt Lever
- Item Dimensions: 4.4 x 3.6 x 1.0 inches
- Item Weight: 0.40 Pounds
- Fitment Type: Direct Replacement
- Part Description: 2008 Chevrolet Impala Tilt Lever
Vehicle Fitment- 2008 Chevrolet Impala | 50th Anniversary Edition, LS, LT, LTZ, Police, SS | 6 Cyl 3.5 L FLEX, 6 Cyl 3.5 L GAS, 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS, 6 Cyl 3.9 L FLEX, 6 Cyl 3.9 L GAS, 8 Cyl 5.3 L GAS
Product Specifications- Notes: Column Shift
- Other Names: Shift Lever
- Item Dimensions: 21.2 x 6.1 x 1.0 inches
- Item Weight: 0.60 Pounds
- Fitment Type: Direct Replacement
- Part Description: 2008 Chevrolet Impala Shift Lever
Vehicle Fitment- 2008 Chevrolet Impala | 50th Anniversary Edition, LS, LT, LTZ, Police, SS | 6 Cyl 3.5 L FLEX, 6 Cyl 3.5 L GAS, 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS, 6 Cyl 3.9 L FLEX, 6 Cyl 3.9 L GAS, 8 Cyl 5.3 L GAS
FAQ for Automatic Transmission Shift Levers Repair
Q: What's the removal procedure for the transmission control?
A:
The removal procedure is to remove the console trim plate, the console wiring harness, the console shift control wiring harness, and the automatic transaxle range selector cable disconnect the lightbulb and the retainer from the shiftier, remove the console shift control retaining nuts and the console shift control assembly.
By Bob
GM Specialist
01/11/2022Q: What's the installation procedure for the transmission control?
A:
The installation procedure is to install the console shift control, and the console shift control retaining nuts and tighten the console shift control retaining nuts to 24 N.m (18 lb-ft), then install the automatic transaxle range selector cable, the console shift control wiring harness, the console wiring harness, and the console trim plate.
By Bob
GM Specialist
01/11/2022Q: What's the recommended torque for the shift lever screw?
A:
The recommended torque is 20 N.m (15 lb-ft).
By Bob
GM Specialist
01/11/2022Q: Where should the shift lever seal be installed?
A:
The shift lever seal must be installed on the narrow end of the shift lever.
By Bob
GM Specialist
01/11/2022