< Back ×
My Vehicle Change Vehicle
2008 Chevrolet Impala
< Back to View All
Brake Dust Shields, Backing Plates & Brake Hardware
- Department
- Brands
- Prices
OEM (Genuine) 2008 Chevrolet Impala Rear Cable
PartNumber: 15242626
Product Specifications- Notes: Impala, Monte Carlo; Left
- Other Names: Park Brake Cable, Rear Cable
- Item Dimensions: 11.6 x 11.2 x 3.7 inches
- Item Weight: 0.60 Pounds
- Fitment Type: Direct Replacement
- Replaces: 10310911, 10405321
- Part Description: 2008 Chevrolet Impala Rear Cable
Vehicle Fitment- 2008 Chevrolet Impala | 50th Anniversary Edition, Base, LS, LS Sport, LT, LTZ, Police, SS | 6 Cyl 3.4 L GAS, 6 Cyl 3.5 L FLEX, 6 Cyl 3.5 L GAS, 6 Cyl 3.8 L GAS, 6 Cyl 3.9 L FLEX, 6 Cyl 3.9 L GAS, 8 Cyl 5.3 L GAS
$30.52 MSRP:$57.58You Save: $27.06 (47%)
Wagner® Parking Brake Cable for 2008 Chevrolet Impala
PartNumber: BC141967Product Specifications- UPC: 008536571407
- Part Description: 2008 Chevrolet Impala Parking Brake Cable
Vehicle Fitment- 2008 Chevrolet Impala | All Trims | All Engines
OEM (Genuine) 2008 Chevrolet Impala Cable Asm-Parking Brake Front
PartNumber: 15297497Product Specifications- Notes: Impala, Monte Carlo
- Other Names: Front Cable
- Item Dimensions: 11.4 x 10.8 x 3.8 inches
- Item Weight: 1.20 Pounds
- Fitment Type: Direct Replacement
- Replaces: 25919312, 10310909
- Part Description: 2008 Chevrolet Impala Cable Asm-Parking Brake Front
Vehicle Fitment- 2008 Chevrolet Impala | 50th Anniversary Edition, Base, LS, LS Sport, LT, LTZ, Police, SS | 6 Cyl 3.4 L GAS, 6 Cyl 3.5 L FLEX, 6 Cyl 3.5 L GAS, 6 Cyl 3.8 L GAS, 6 Cyl 3.9 L FLEX, 6 Cyl 3.9 L GAS, 8 Cyl 5.3 L GAS
OEM (Genuine) 2008 Chevrolet Impala Cable Asm-Parking Brake Rear
PartNumber: 15297496
Product Specifications- Notes: Impala, Monte Carlo; Right
- Other Names: Park Brake Cable, Rear Cable
- Item Dimensions: 30.6 x 9.6 x 1.3 inches
- Item Weight: 0.60 Pounds
- Fitment Type: Direct Replacement
- Replaces: 10310910
- Part Description: 2008 Chevrolet Impala Cable Asm-Parking Brake Rear
Vehicle Fitment- 2008 Chevrolet Impala | 50th Anniversary Edition, Base, LS, LS Sport, LT, LTZ, Police, SS | 6 Cyl 3.4 L GAS, 6 Cyl 3.5 L FLEX, 6 Cyl 3.5 L GAS, 6 Cyl 3.8 L GAS, 6 Cyl 3.9 L FLEX, 6 Cyl 3.9 L GAS, 8 Cyl 5.3 L GAS
FAQ for Parking Brake Cable Repair
Q: What's the recommended torque for the wheel drive shaft nut?
A:
The recommended torque is 260 Nm (192 lb-ft).
By Bob
GM Specialist
02/11/2022Q: What's the removal procedure for the park brake cable equalizer?
A:
The removal procedure is to raise and support the vehicle, disconnect the left rear park brake cable and adjustment stud assembly from the equalizer assembly by removing the equalizer nut from the adjustment stud, disconnect the front park brake cable from the right rear cable at the connector clip, then remove the equalizer assembly.
By Bob
GM Specialist
02/11/2022Q: What should be done before removing the wheel bearing/hub?
A:
You will need to raise and support the vehicle.
By Bob
GM Specialist
02/11/2022Q: How to remove the front wheel stud?
A:
You will need to raise and support the vehicle, remove the tire and wheel and the brake rotor, then use the J 35917 to press the wheel stud from the bearing/hub.
By Bob
GM Specialist
02/11/2022Q: What should be noticed if you are replacing the wheel(s), the wheel stud(s), the wheel nut(s), or the wheel bolt(s)?
A:
You will need to install only new GM original equipment parts. Installation of used parts or non-GM original equipment parts may cause the wheel to loosen, loss of tire air pressure, poor vehicle handling, and loss of vehicle control resulting in personal injury.
By Bob
GM Specialist
02/11/2022Q: What's the installation procedure for the park brake cable equalizer?
A:
The installation procedure is to install the equalizer assembly, connect the front brake cable to the right rear cable, connect the left rear brake cable and adjustment stud assembly to the equalizer assembly, then adjust the Park Brake System and lower the vehicle.
By Bob
GM Specialist
02/11/2022Q: What's the recommended torque for the wheel bearing/hub bolts?
A:
The recommended torque is 130 Nm (96 lb-ft).
By Bob
GM Specialist
02/11/2022See more FAQs (2)