Search Bar
Search by Part Number, Part Name, or Vehicle
  • My Garage
  • Cart
  • OE Parts
  • Body & Mirrors
  • Chassis & Brakes
  • Engine & Drivetrain
  • Electrical & Lighting
Help Center
< Back ×
  • Shop OE Parts
  • Shop By Category
  • Body & Mirrors
  • Chassis & Brakes
  • Engine & Drivetrain
  • Electrical & Lighting

2009 Cadillac XLR Hood Lift Support

My Vehicle Change Vehicle
2009 Cadillac XLR
Change Vehicle
Vehicle Options
We need more information about your vehicle to make a correct determination of fitment
< Back to View All
Lift Supports
  • Department
  • Brands
  • Prices

2 Products found

2 Q&A for Hood Lift Support Repair
Sort by:
Recommended
Filter Results
Sort
View by
  • OEM 2009 Cadillac XLR Lift Cylinder - 10446862
    OEM 2009 Cadillac XLR Lift Cylinder Diagram - 10446862
    View Related Parts

    OEM (Genuine) 2009 Cadillac XLR Lift Cylinder

    PartNumber: 10446862
    $28.75 MSRP: $45.67
    You Save: $16.92 (38%)
    Product Specifications
    • Location: Driver Side; Passenger Side
    • Other Names: Lift Cylinder
    • Item Dimensions: 4.3 x 4.2 x 39.6 inches
    • Item Weight: 0.90 Pounds
    • Fitment Type: Direct Replacement
    • Part Description: 2009 Cadillac XLR Lift Cylinder
    More Info
    Vehicle Fitment
    • 2009 Cadillac XLR | Base, Platinum, V | 8 Cyl 4.4 L GAS, 8 Cyl 4.6 L GAS
  • StrongArm Hood Lift Support for 2009 Cadillac XLR - 6241

    StrongArm® Hood Lift Support for 2009 Cadillac XLR

    PartNumber: 6241
    $22.56
    Product Specifications
    • Body: 18.00
    • BODY CONNECTION: ball socket (nylon) 8mm
    • Brackets: No
    • Compressed Length: 17.81
    • Extended Length: 27.81
    • Force: 44.00
    • Hardware Kit: No
    • High Performance Item: N
    • Internal Springs: No
    • Is Application Specific: Y
    • Material: Heavy gauge steel pressure tube provides long life; Rubber o-ring piston seal for controlled lift; Teflon backup ring gives enhanced performance
    • Shaft: 8.00
    • SHAFT CONNECTION: ball socket (nylon) 10mm
    • Stroke: 10.00
    • UPC: 845998015656
    • Part Description: 2009 Cadillac XLR Hood Lift Support
    More Info
    Vehicle Fitment
    • 2009 Cadillac XLR | All Trims | All Engines

FAQ for Hood Lift Support Repair

Q: What is the hood open assist rod installation procedure?
A:
Install the hood assist rod to the vehicle and the upper hood assist rod ball stud attached to the hood. Next, install the hood assist rod onto the lower hood assist rod ball stud and make sure the clips are fully seated.
By Bob
GM Specialist
01/11/2022
Q: What is the hood open assist rod stud installation procedure?
A:
Install the lower hood assist rod ball stud to the front structure and tighten it to 9 Nm. Next, install the hood assist rod and make sure the clip is fully seated.
By Bob
GM Specialist
01/11/2022

FAQ for Other Repair Info

Q: What is the proper way to remove the door lock switch?
A:
The proper way is to remove the door trim panel, the retainer screws, and the power Door Lock Switch.
Q: What is the hood primary and secondary latch installation procedure?
A:
First, install the Hood Latch to the latch support, install the bolts attaching the latch to the latch support, and tighten to 9 Nm. Next, connect the hood release cable to the latch and the secondary latch cable to the latch. Lower the hood and check the latch for proper alignment. Finally, install the front section of the air cleaner assembly.
Q: What is the hood primary latch release cable installation procedure?
A:
Position the Hood Release Cable to the vehicle and install the hood release cable grommet to the front of the dash panel. Next, install the screws securing the hood release handle to the vehicle and tighten to 2 Nm. After that install the hood release cable to the clips retaining the cable to the vehicle. Connect the hood release cable to the hood latch and install all related panels/components.