Search Bar
Search by Part Number, Part Name, or Vehicle
  • My Garage
  • Cart
  • OE Parts
  • Body & Mirrors
  • Chassis & Brakes
  • Engine & Drivetrain
  • Electrical & Lighting
Help Center
< Back ×
  • Shop OE Parts
  • Shop By Category
  • Body & Mirrors
  • Chassis & Brakes
  • Engine & Drivetrain
  • Electrical & Lighting

2009 Chevrolet Avalanche Rack and Pinion Seal

My Vehicle Change Vehicle
2009 Chevrolet Avalanche
Change Vehicle
Vehicle Options
We need more information about your vehicle to make a correct determination of fitment
< Back to View All
Steering Racks & Gearboxes
  • Department
  • Brands
  • Prices

2 Products found

4 Q&A for Rack And Pinion Seal Repair
Sort by:
Recommended
Filter Results
Sort
View by
  • Gates Rack And Pinion Seal Kit for 2009 Chevrolet Avalanche - 348653

    Gates® Rack And Pinion Seal Kit for 2009 Chevrolet Avalanche

    PartNumber: 348653
    Product Specifications
    • UPC: 770075548522
    • Part Description: 2009 Chevrolet Avalanche Rack And Pinion Seal Kit
    Vehicle Fitment
    • 2009 Chevrolet Avalanche | All Trims | 8 Cyl 6.0L
    • 2009 Chevrolet Avalanche | All Trims | 8 Cyl 5.3L
  • OEM 2009 Chevrolet Avalanche Ring-Steering Gear Stub Shaft Seal Retainer Diagram - 15776969
    View Related Parts

    OEM (Genuine) 2009 Chevrolet Avalanche Ring-Steering Gear Stub Shaft Seal Retainer

    PartNumber: 15776969
    Product Specifications
    • Other Names: Gear Assembly Upper Seal, Upper Seal
    • Item Dimensions: 2.2 x 2.2 x 0.4 inches
    • Item Weight: 0.30 Pounds
    • Fitment Type: Direct Replacement
    • Part Description: 2009 Chevrolet Avalanche Ring-Steering Gear Stub Shaft Seal Retainer
    More Info
    Vehicle Fitment
    • 2009 Chevrolet Avalanche | Black Diamond LS, Black Diamond LT, Black Diamond LTZ, LS, LT, LTZ | 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L GAS

FAQ for Rack And Pinion Seal Repair

Q: What is the proper way to remove the drive pinion flange?
A:
The proper way is to remove the rear wheel axle shafts, the rear brake rotors, the propeller shafts, and the drive pinion seal.
By Bob
GM Specialist
02/11/2022
Q: What is the proper way to remove the drive pinion housing?
A:
The proper way is to drain the axle lubricant and remove the propeller shaft, the axle shafts, and the bearing cup.
By Bob
GM Specialist
02/11/2022
Q: How do you install the drive pinion flange?
A:
You can install the washer, the propeller shaft, the axle shafts, and the brake rotors.
By Bob
GM Specialist
02/11/2022
Q: How do you install the drive pinion housing?
A:
You can install the pinion gear bearing retainer, the propeller shaft, and the axle shafts, and fill up the axle.
By Bob
GM Specialist
02/11/2022

FAQ for Other Repair Info

Q: How do you install the steering shaft coupling?
A:
You can install the Steering Shaft coupling, the steering shaft coupling nut, and the engine shield.
Q: What is the power vacuum brake booster installation procedure?
A:
Install a new Brake Booster gasket, the power vacuum brake booster, and the brake booster nuts. Make sure to tighten the nuts to 33 Nm, connect the brake booster pushrod to the brake pedal pivot and install the stop lamp switch. Next, install the brake booster pushrod retainer, and the retainer bolt and tighten to 10 Nm. Install the vacuum hose to the check valve, and install the master cylinder and the 2 master cylinder nuts. Tighten the nuts to 33 Nm.
Q: What is the rear brake hose service procedure?
A:
Make sure to remove dirt/debris from the brake pipe fitting. Use a backup wrench when removing or installing the brake pipe fitting. Tighten the Brake Hose to the axle bolt to 9 Nm.