< Back ×
My Vehicle Change Vehicle
2009 Chevrolet Suburban 1500
< Back to View All
Air Filters & Intake Systems
- Department
- Prices
OEM (Genuine) 2009 Chevrolet Suburban 1500 Manifold
PartNumber: 12620308
Product Specifications- Notes: Yukon XL, Suburban; 5.3L
- Other Names: Intake Manifold, Manifold
- Item Dimensions: 28.4 x 18.3 x 12.8 inches
- Item Weight: 17.50 Pounds
- Fitment Type: Direct Replacement
- Replaces: 12597598
- Part Description: 2009 Chevrolet Suburban 1500 Manifold
Vehicle Fitment- 2009 Chevrolet Suburban 1500 | LS, LT, LTZ | 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L GAS
$206.56 MSRP:$341.89You Save: $135.33 (40%)OEM (Genuine) 2009 Chevrolet Suburban 1500 Manifold
PartNumber: 12597600
Product Specifications- Notes: Escalade Esv;Yukon XL, Suburban; 6.0L, 6.2L
- Other Names: Intake Manifold, Manifold
- Item Dimensions: 29.5 x 19.2 x 13.3 inches
- Item Weight: 17.00 Pounds
- Fitment Type: Direct Replacement
- Part Description: 2009 Chevrolet Suburban 1500 Manifold
Vehicle Fitment- 2009 Chevrolet Suburban 1500 | LT, LTZ | 8 Cyl 6.0 L GAS
$176.82 MSRP:$292.66You Save: $115.84 (40%)
FAQ for Intake Manifold Repair
Q: How do I remove the Engine Block Valley Cover?
A:
You should remove the intake manifold, remove the engine valley cover bolts, remove the engine valley cover and gasket, remove the O-ring seals from the cover and remove the oil pressure sensor and washer.
By Bob
GM Specialist
01/11/2022Q: What should be noticed when replacing Intake Manifold (RPOs LC9, LMG, LY5, L76)?
A:
You should remove the engine harness retainer from the stud and locator, disconnect the engine harness electrical connector from the evaporative emission (EVAP) canister purge solenoid, and disconnect the engine wiring harness electrical connector from the manifold absolute pressure (MAP) sensor. You should evenly push in the RED collar to remove the nipple.
By Bob
GM Specialist
01/11/2022Q: How do I remove the Upper Intake Manifold Cover?
A:
You should remove the intake manifold, reposition the brake booster vacuum hose clamp at the intake manifold, remove the brake booster vacuum hose from the intake manifold nipple, remove the upper intake manifold cover nut and remove the upper intake manifold cover.
By Bob
GM Specialist
01/11/2022Q: How do I remove the Upper Intake Manifold Sight Shield?
A:
You should open the hood, grasp the front of the intake manifold sight shield and disengage the grommets from the studs, remove the intake manifold sight shield from the retainer slots and remove the intake manifold sight shield retainer bolts and retainer if required.
By Bob
GM Specialist
01/11/2022Q: How do I install the Upper Intake Manifold Sight Shield?
A:
You should position the intake manifold sight shield on top of the intake manifold, install the intake manifold sight shield retainer bolts, install the intake manifold sight shield tabs into the slots in the retainer, align the intake manifold sight shield grommets with the studs, push down on the intake manifold sight shield over the grommets, seating the intake manifold sight shield and close the hood.
By Bob
GM Specialist
01/11/2022Q: What is the recommended torque when installing the fuel rail bolts?
A:
The recommended torque is 10 Nm(89 lb in).
By Bob
GM Specialist
01/11/2022Q: How do I install the Upper Intake Manifold Cover?
A:
You should install the upper intake manifold cover, install the upper intake manifold cover nut until snug, install the brake booster vacuum hose to the intake manifold nipple, position the brake booster vacuum hose clamp at the intake manifold and install the intake manifold.
By Bob
GM Specialist
01/11/2022See more FAQs (2)