< Back ×
My Vehicle Change Vehicle
2009 Chevrolet Tahoe
< Back to View All
Driveline, Axles & 4WD
- Department
- Prices
OEM (Genuine) 2009 Chevrolet Tahoe Boot Kit, Front Wheel Drive Shaft Cv Joint
PartNumber: 19256071
Product Specifications- Notes: 4WD; Tahoe, Yukon, Escalade
- Location: Driver Side; Passenger Side
- Item Dimensions: 6.4 x 6.3 x 5.7 inches
- Item Weight: 1.70 Pounds
- Fitment Type: Direct Replacement
- Replaces: 26069246, 15868187
- Part Description: 2009 Chevrolet Tahoe Boot Kit, Front Wheel Drive Shaft Cv Joint
Vehicle Fitment- 2009 Chevrolet Tahoe | Base, Hybrid, LS, LT, LTZ, PPV, Premier, SSV, Z71 | 8 Cyl 4.8 L GAS, 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 5.7 L GAS, 8 Cyl 6.0 L ELECTRIC/FLEX, 8 Cyl 6.0 L ELECTRIC/GAS, 8 Cyl 6.2 L FLEX, 8 Cyl 6.2 L GAS
$104.98 MSRP:$182.69You Save: $77.71 (43%)
OEM (Genuine) 2009 Chevrolet Tahoe Inner Boot
PartNumber: 26062615
Product Specifications- Notes: 4WD; Tahoe, Yukon, Escalade
- Location: Driver Side; Passenger Side
- Other Names: Inner Boot
- Item Dimensions: 6.7 x 6.1 x 5.8 inches
- Item Weight: 1.60 Pounds
- Fitment Type: Direct Replacement
- Part Description: 2009 Chevrolet Tahoe Inner Boot
Vehicle Fitment- 2009 Chevrolet Tahoe | Base, Hybrid, Limited, LS, LT, LTZ, Z71 | 8 Cyl 4.8 L GAS, 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 5.7 L GAS, 8 Cyl 6.0 L ELECTRIC/FLEX, 8 Cyl 6.0 L ELECTRIC/GAS, 8 Cyl 6.2 L FLEX, 8 Cyl 6.2 L GAS, 8 Cyl 6.5 L DIESEL
$27.28 MSRP:$43.53You Save: $16.25 (38%)
FAQ for Cv Joint Boot Repair
Q: What special tools will I be needing when replacing the Wheel Drive Shaft Outer Joint and Boot?
A:
You will be needing snap ring pliers, drive axle seal clamp pliers, a drive axle clamp swage tool, and an axle swage tool.
By Bob
GM Specialist
01/11/2022Q: What special tools will I be needing when replacing the Wheel Drive Shaft Inner Joint and Boot?
A:
You will be needing drive axle seal clamp pliers, a drive axle clamp swage tool, and an axle swage tool.
By Bob
GM Specialist
01/11/2022Q: How do you remove the Wheel Drive Shaft Inner Joint and Boot?
A:
You need to remove the wheel drive shaft, use the appropriate tool to remove the boot clamp, remove the tripot housing and any grease from the housing, use side cutters to remove the small boot retaining clamp, use the appropriate tool to remove the retaining ring, then the spider assembly, and the boot, and use the appropriate tool to remove any rust in the seal mounting area (grooves). If any of the internal components of the tripot assembly are found to be damaged or have excessive wear, replace the tripot as an assembly.
By Bob
GM Specialist
01/11/2022Q: What should be cleaned with cleaning solvent?
A:
You need to clean the inner and outer race assemblies, the CV joint cage, and the chrome alloy balls.
By Bob
GM Specialist
01/11/2022