< Back ×
My Vehicle Change Vehicle
2009 Chevrolet Tahoe
< Back to View All
Cameras & Driver Safety
- Department
- Prices
OEM (Genuine) 2009 Chevrolet Tahoe Reverse Sensor
PartNumber: 15239247
Product Specifications- Notes: Reverse Sensing System; Tahoe, Yukon, Escalade;Tahoe, Yukon, Escalade; Rear Object; Tahoe 2009-14 W/O Ltz, Yukon W/O Denali; Yukon W/Denali, Tahoe 2009-14 W/Ltz
- Other Names: Alarm, Park Sensor, Reverse Sensor, Sensor
- Item Dimensions: 4.8 x 2.3 x 1.9 inches
- Item Weight: 0.30 Pounds
- Fitment Type: Direct Replacement
- Replaces: 19116085
- Part Description: 2009 Chevrolet Tahoe Reverse Sensor
Vehicle Fitment- 2009 Chevrolet Tahoe | Hybrid, LS, LT, LTZ | 8 Cyl 4.8 L GAS, 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L ELECTRIC/FLEX, 8 Cyl 6.0 L ELECTRIC/GAS, 8 Cyl 6.2 L FLEX, 8 Cyl 6.2 L GAS
$162.05 MSRP:$244.48You Save: $82.43 (34%)
OEM (Genuine) 2009 Chevrolet Tahoe Object Sensor
PartNumber: 20823460
Product Specifications- Notes: Tahoe, Yukon, Escalade; Side Object
- Other Names: Module, Object Sensor, Sensor
- Item Dimensions: 5.6 x 4.6 x 1.4 inches
- Item Weight: 1.00 Pounds
- Fitment Type: Direct Replacement
- Replaces: 1999430, 25978649, 25910830, 20759899, 01999430
- Part Description: 2009 Chevrolet Tahoe Object Sensor
Vehicle Fitment- 2009 Chevrolet Tahoe | Hybrid, LS, LT, LTZ | 8 Cyl 5.3 L FLEX, 8 Cyl 6.0 L ELECTRIC/FLEX, 8 Cyl 6.0 L ELECTRIC/GAS
$422.21 MSRP:$636.96You Save: $214.75 (34%)
FAQ for Parking Sensors Repair
Q: How do you install the Rear Object Sensor?
A:
You need to paint the rear object sensor, ensure the paint does not exceed 6 mils, insert the sensor into the housing, connect the electrical connector to the rear object sensor and install the rear bumper fascia.
By Bob
GM Specialist
02/11/2022Q: How do you remove the rear object sensor?
A:
You need to remove the rear bumper fascia, disconnect the electrical from the rear object sensor and lift the locking tabs on the housing and remove the rear object sensor.
By Bob
GM Specialist
02/11/2022Q: How to replace the Rear Object Sensor Housing?
A:
You need to remove the rear fascia, disconnect the sensor harness, remove the sensor from the sensor housing, sand/grind sonic weld plastic residue from the fascia, apply structural adhesive epoxy, Lord Fusor(TM)127EZ or equivalent, to fascia at the mating surface, use the alignment tabs to install the sensor housing to the fascia, allow adhesive to cure according to manufacturer's direction, install the sensor to the sensor housing, connect the electrical harness and install the rear fascia.
By Bob
GM Specialist
02/11/2022Q: How many screws does the Information Center Telltale have?
A:
It has a total of 2 screws.
By Bob
GM Specialist
01/11/2022Q: What should be noticed when replacing the Information Center Telltale Assembly?
A:
You need to disconnect the electrical connector.
By Bob
GM Specialist
01/11/2022Q: What is the recommended torque for the Rear Object Alarm Module nut?
A:
The recommended torque is 2 Nm(18 lb in).
By Bob
GM Specialist
01/11/2022Q: How many nuts does the Rear Object Alarm Module have?
A:
It has a total of 3 nuts.
By Bob
GM Specialist
01/11/2022Q: How do I replace the Rear Object Alarm Module?
A:
You need to position the carpet to access the module, disconnect the electrical connector and reprogram the rear object alarm module after replacement.
By Bob
GM Specialist
01/11/2022Q: What is the recommended torque for the Information Center Telltale Screw?
A:
The recommended torque is 2 Nm(18 lb in).
By Bob
GM Specialist
01/11/2022See more FAQs (4)