Search Bar
Search by Part Number, Part Name, or Vehicle
  • My Garage
  • Cart
  • OE Parts
  • Body & Mirrors
  • Chassis & Brakes
  • Engine & Drivetrain
  • Electrical & Lighting
Help Center
< Back ×
  • Shop OE Parts
  • Shop By Category
  • Body & Mirrors
  • Chassis & Brakes
  • Engine & Drivetrain
  • Electrical & Lighting

2009 GMC Envoy Brake Master Cylinder Bleeder Tool

My Vehicle Change Vehicle
2009 GMC Envoy
Change Vehicle
Vehicle Options
We need more information about your vehicle to make a correct determination of fitment
< Back to View All
Brake Boosters & Brake Master Cylinders
  • Department
  • Brands
  • Prices

1 Product found

4 Q&A for Brake Master Cylinder Bleeder Tool Repair
Sort by:
Recommended
Filter Results
Sort
View by
  • Cardone Reman Master Cylinder Bleeding Tool for 2009 GMC Envoy - 10-5000MCB

    Cardone Reman® Master Cylinder Bleeding Tool for 2009 GMC Envoy

    PartNumber: 10-5000MCB
    Product Specifications
    • Bleeder Adapters Included: No
    • Bleeder Pressure Gauge Included: No
    • Bleeder Tubing Included: No
    • E-Waste: No
    • Material: Plastic
    • Package Contents: Bleeder Tool
    • Product Condition: New
    • UPC: 082617849678
    • Part Description: 2009 GMC Envoy Master Cylinder Bleeding Tool
    More Info
    Vehicle Fitment
    • 2009 GMC Envoy | All Trims | All Engines

FAQ for Brake Master Cylinder Bleeder Tool Repair

Q: Can you reuse the brake fluid that is used during bleeding?
A:
No, do not reuse the brake fluid that is used during bleeding.
By Bob
GM Specialist
28/10/2022
Q: How should you deal with it properly if the brake fluid was not contaminated with an oil-based or a silicone-based substance, but was contaminated with water or dirt, rust, or corrosion?
A:
You need to replace the brake master cylinder reservoir cap diaphragm then.
By Bob
GM Specialist
28/10/2022
Q: What should you notice when the brake system warning lamp remains illuminated?
A:
In this situation, do not allow the vehicle to be driven until it is diagnosed and repaired.
By Bob
GM Specialist
28/10/2022
Q: What kind of special tools will be used in the Hydraulic Brake System Bleeding (Pressure)?
A:
J-29532-Diaphragm Pressure Bleeder, or equivalent, J-35589-A-Brake Pressure Bleeder Adapter.
By Bob
GM Specialist
28/10/2022

FAQ for Other Repair Info

Q: What is the removal procedure for the Power Brake Booster Vacuum Sensor?
A:
Place the ignition switch in the OFF position, apply and release the brake pedal several times until the pedal becomes firm to deplete the power vacuum Brake Booster vacuum reserve, disconnect the power brake booster vacuum sensor electrical connector, and remove the power brake booster vacuum sensor.
Q: What kind of special tools will be used when removing the Master Cylinder Bench Bleeding?
A:
Secure the mounting flange of the Brake Master Cylinder in a bench vise, remove the master cylinder reservoir cap and diaphragm, install suitable fittings to the master cylinder ports and also provide for hose attachment, and install transparent hoses to the fittings installed to the master cylinder ports, then route the hoses into the master cylinder reservoir, fill the master cylinder reservoir to at least the half-way point with GM approved brake fluid from a clean, sealed brake fluid container, release the primary piston as far as it will travel, a depth of about 25 mm (1 in), several times, continue to depress and release the primary piston until fluid flows freely from the ports with no evidence of air bubbles, remove the transparent hoses from the master cylinder reservoir, install the master cylinder reservoir cap and diaphragm, remove the fittings with the transparent hoses from the master cylinder ports, and remove the master cylinder from the vise.