Search Bar
Search by Part Number, Part Name, or Vehicle
  • My Garage
  • Cart
  • OE Parts
  • Body & Mirrors
  • Chassis & Brakes
  • Engine & Drivetrain
  • Electrical & Lighting
Help Center
< Back ×
  • Shop OE Parts
  • Shop By Category
  • Body & Mirrors
  • Chassis & Brakes
  • Engine & Drivetrain
  • Electrical & Lighting

2010 Cadillac SRX Rain Sensors

My Vehicle Change Vehicle
2010 Cadillac SRX
Change Vehicle
Vehicle Options
We need more information about your vehicle to make a correct determination of fitment
< Back to View All
Wipers & Washers
  • Department
  • Prices

2 Products found

1 Q&A for Rain Sensors Repair
Sort by:
Recommended
Filter Results
Sort
View by
  • OEM 2010 Cadillac SRX Sensor - 95157887
    OEM 2010 Cadillac SRX Sensor Diagram - 95157887
    View Related Parts

    OEM (Genuine) 2010 Cadillac SRX Sensor

    PartNumber: 95157887
    $50.69 MSRP: $76.48
    You Save: $25.79 (34%)
    Product Specifications
    • Other Names: Rain Sensor, Sensor
    • Item Dimensions: 3.8 x 2.9 x 1.4 inches
    • Item Weight: 0.40 Pounds
    • Fitment Type: Direct Replacement
    • Replaces: 13317106
    • Part Description: 2010 Cadillac SRX Sensor
    More Info
    Vehicle Fitment
    • 2010 Cadillac SRX | Base, Luxury, Performance, Premium | 6 Cyl 2.8 L GAS, 6 Cyl 3.0 L GAS, 6 Cyl 3.6 L FLEX
  • OEM 2010 Cadillac SRX In-Car Sensor - 13231068
    OEM 2010 Cadillac SRX In-Car Sensor Diagram - 13231068
    View Related Parts

    OEM (Genuine) 2010 Cadillac SRX In-Car Sensor

    PartNumber: 13231068
    $52.21 MSRP: $98.54
    You Save: $46.33 (48%)
    Product Specifications
    • Item Dimensions: 1.9 x 1.7 x 0.4 inches
    • Item Weight: 0.30 Pounds
    • Fitment Type: Direct Replacement
    • Part Description: 2010 Cadillac SRX In-Car Sensor
    More Info
    Vehicle Fitment
    • 2010 Cadillac SRX | Base, Luxury, Performance, Premium | 6 Cyl 2.8 L GAS, 6 Cyl 3.0 L GAS, 6 Cyl 3.6 L FLEX

FAQ for Rain Sensors Repair

Q: How to replace the windshield outside moisture sensor?
A:
You should first unsnap the mounting plate cover from the windshield outside moisture sensor bracket, remove the right side from the left side to clear the inside rearview mirror, and squeeze the outside moisture sensor tabs to disengage the windshield outside moisture sensor from the outside moisture sensor bracket tabs. Then, you should disengage the electrical connector from the moisture sensor and remove the windshield outside moisture sensor from the outside moisture sensor bracket.
By Bob
GM Specialist
01/11/2022

FAQ for Other Repair Info

Q: How to replace the rear window wiper blade?
A:
You should carefully release the finish cover locking tabs securing the finish cover to the rear wiper arm, lift the wiper arm away from the rear liftgate window, rotate slightly the bottom edge of the blade away from the underside of the arm, push in the bottom of the Wiper Blade clip and remove the wiper blade from the inside radius of the wiper arm.
Q: How to replace the windshield washer solvent level switch?
A:
You should remove the left front wheelhouse liner, drain the windshield washer solvent into a suitable clean container, disconnect the electrical connector to the level sensor switch, use two suitable flat-bladed tools to remove the level sensor switch from the windshield washer container, and finally discard the level sensor grommet.
Q: What do we need to note when we release the headlamp washer pump from the headlamp washer pump grommet?
A:
You should use full-strength washer solvent on the new grommet to aid in the installation of the new headlamp washer pump.