Contact Us Live Chat or 1-888-220-8330
Search Bar
Search by Part Number or Keywords
  • My Garage
  • My Account
  • Cart
  • Body & Mirrors
  • Chassis & Brakes
  • Engine & Drivetrain
  • Electrical & Lighting
Help Center
< Back ×
  • Body & Mirrors
  • Chassis & Brakes
  • Engine & Drivetrain
  • Electrical & Lighting
Login/Register My Account Track Order Help Center Contact Us
Replacement and OEM Parts for 2010 Chevrolet Aveo Clutch Forks

2010 Chevrolet Aveo Clutch Forks

My Vehicle Change Vehicle
2010 Chevrolet Aveo
Change Vehicle
Vehicle Options
We need more information about your vehicle to make a correct determination of fitment
< Back to View All
Clutches, Linkages & Flywheels
  • Department
  • Prices

1 Product found

2 Q&A for Clutch Forks Repair
Show Item:
  • 30
  • 60
  • 90
Sort by:
Recommended
Filter
Sort
View by
  • OEM 2010 Chevrolet Aveo Release Fork Diagram - 94580796
    View Related Parts

    OEM (Genuine) 2010 Chevrolet Aveo Release Fork

    PartNumber: 94580796
    OEM 2010 Chevrolet Aveo Release Fork - 94580796
    Product Specifications
    • Notes: Aveo, Aveo5
    • Other Names: Release Fork
    • Item Dimensions: 3.6 x 3.6 x 1.4 inches
    • Item Weight: 0.60 Pounds
    • Fitment Type: Direct Replacement
    • Part Description: 2010 Chevrolet Aveo Release Fork
    More Info
    Vehicle Fitment
    • 2010 Chevrolet Aveo | Base, LS, LT, Special Value | 4 Cyl 1.6 L GAS
    $15.74 MSRP: $26.03
    You Save: $10.29 (40%)

FAQ for Clutch Forks Repair

Q: What is the clutch pedal cruise control release switch installation procedure?
A:
First place the cruise control clutch switch pedal support and connect the cruise control clutch pedal switch electrical connector. Next, adjust the cruise control clutch pedals switch.
By Bob
GM Specialist
21/01/2022
Q: What is the cruise control clutch switch adjustment?
A:
First, push the switch assembly through the pedal support and turn 90 degrees. Next, hold the clutch pedal to the rest position and connect the cruise control clutch pedal switch electrical connector.
By Bob
GM Specialist
21/01/2022

FAQ for Other Repair Info

Q: How do I install the Clutch Master Cylinder?
A:
Start with installing the Clutch Master Cylinder by tightening the nuts to 22 Nm (16 LB-FT). Install the master cylinder pipe. Connect the master cylinder hose and the hose clamp on the master cylinder. Next, install the push rod fixing pin, push rod, and locking clip. Bleed the air and adjust the pedal. Lastly, fill the reservoir to the max level.
Q: How do I install the Clutch, Pressure Plate, and Pilot Bearing?
A:
Lubricate the spline on the clutch disc with multi-purpose grease, and next align the pressure plate and the clutch disc onto the flywheel. Install the pressure plate bolts and remove the Clutch Center Guide from the clutch assembly. Next, install the transaxle into the vehicle and connect the negative battery cable.
Q: How do I remove the Release Bearing?
A:
Start with removing the transaxle from the vehicle, then remove the release arm, the release bearing, the release shaft and bushing, the No. 2 bushing, and the seal, the release shaft. Next thread the tap (M16 x 1.51) (2) into the bushing. Connect the sliding shaft and the end of the bushing remover.