< Back ×
My Vehicle Change Vehicle
2010 Chevrolet Cobalt
< Back to View All
Power Sunroof & Convertible Top
- Department
- Prices
OEM (Genuine) 2010 Chevrolet Cobalt Motor Asm-Sun Roof Actuator
PartNumber: 25920112
Product Specifications- Notes: Coupe; Cobalt; Sedan
- Other Names: Motor
- Item Dimensions: 9.3 x 5.1 x 3.2 inches
- Item Weight: 2.20 Pounds
- Fitment Type: Direct Replacement
- Replaces: 15845680, 22721264
- Part Description: 2010 Chevrolet Cobalt Motor Asm-Sun Roof Actuator
Vehicle Fitment- 2010 Chevrolet Cobalt | Base, LS, LT, LTZ, Sport, SS | 4 Cyl 2.0 L GAS, 4 Cyl 2.2 L GAS, 4 Cyl 2.4 L GAS
FAQ for Sunroof Motor Repair
Q: How do you adjust the sunroof window?
A:
You can loosen the adjusting screws, adjust the corners, and tighten the adjustment screws.
By Bob
GM Specialist
16/01/2022Q: How do you install the sunroof actuator motor?
A:
You can plug the motor into the harness, make sure the sunroof is functioning, and install the sunroof motor, and the window.
By Bob
GM Specialist
15/01/2022Q: How do you install the sunroof motor/actuator?
A:
You can install the sunroof motor, connect the electrical connector, and install the headliner.
By Omar
GM Specialist
15/01/2022Q: What is the removal procedure for the sunroof motor/actuator?
A:
The procedure is to disconnect the motor/actuator, and electrical connector, and remove the sunroof actuator.
By Omar
GM Specialist
11/01/2022Q: What is the sunroof housing front drain hose removal procedure?
A:
Remove the front drain hose from the sunroof module and the sunroof drain hose from the attachment points on the windshield pillar. Next, remove the carpet retainer and the hinge pillar inner insulators. Finally, remove the hose through the top of the I/P and disconnect the string from the hose.
By Bob
GM Specialist
10/01/2022Q: What is the sunroof housing rear drain hose installation procedure?
A:
First, route the rear drain hose down the rear window pillar and connect the rear drain hose to the sunroof module. Next, connect the rear drain hose to the attachments on the rear window pillar and install the rear compartment trim panel. Finally, install the headliner.
By Omar
GM Specialist
10/01/2022Q: What is the sunroof housing rear drain hose removal procedure?
A:
Remove the rear drain hose from the sunroof module and the rear compartment trim panel. Pull the sunroof drain hose and grommet out of the rear compartment panel. Finally, pull the rear drain hose out of the rear compartment.
By Bob
GM Specialist
10/01/2022Q: What is the sunroof opening trim finish lace installation procedure?
A:
First, place the end of the sunroof finishing lace at the center of the rear of the sunroof opening and push the finishing lace onto the track assembly flange. Next, pull the finishing lace drawcord towards the sunroof opening and make sure the finishing lace is properly seated over the outer surface of the headliner.
By Omar
GM Specialist
10/01/2022Q: What is the sunroof opening trim finish lace removal procedure?
A:
Pull the sunroof finishing lace from the sunroof window and remove the sunroof finishing lace from the track assembly.
By Bob
GM Specialist
10/01/2022Q: What is the sunroof switch installation procedure?
A:
First, connect the harness to the switch and install the sunroof control switch to the metal housing in the headliner. Next, press the bezel to the headliner to engage the clips.
By Bob
GM Specialist
10/01/2022See more FAQs (7)