Search Bar
Search by Part Number, Part Name, or Vehicle
  • My Garage
  • Cart
  • OE Parts
  • Body & Mirrors
  • Chassis & Brakes
  • Engine & Drivetrain
  • Electrical & Lighting
Help Center
< Back ×
  • Shop OE Parts
  • Shop By Category
  • Body & Mirrors
  • Chassis & Brakes
  • Engine & Drivetrain
  • Electrical & Lighting

2010 Chevrolet Colorado CV Joint Boot

My Vehicle Change Vehicle
2010 Chevrolet Colorado
Change Vehicle
Vehicle Options
We need more information about your vehicle to make a correct determination of fitment
< Back to View All
Driveline, Axles & 4WD
  • Department
  • Prices

2 Products found

4 Q&A for Cv Joint Boot Repair
Sort by:
Recommended
Filter Results
Sort
View by
  • OEM 2010 Chevrolet Colorado Boot Kit, Front Wheel Drive Shaft Cv Joint (Inboard & Outboard) - 89040354
    OEM 2010 Chevrolet Colorado Boot Kit, Front Wheel Drive Shaft Cv Joint (Inboard & Outboard) Diagram - 89040354
    View Related Parts

    OEM (Genuine) 2010 Chevrolet Colorado Boot Kit, Front Wheel Drive Shaft Cv Joint (Inboard & Outboard)

    PartNumber: 89040354
    Product Specifications
    • Notes: 4WD; Canyon, Colorado
    • Location: Driver Side; Passenger Side
    • Other Names: Outer Boot
    • Item Dimensions: 7.6 x 6.9 x 6.8 inches
    • Item Weight: 2.20 Pounds
    • Fitment Type: Direct Replacement
    • Part Description: 2010 Chevrolet Colorado Boot Kit, Front Wheel Drive Shaft Cv Joint (Inboard & Outboard)
    More Info
    Vehicle Fitment
    • 2010 Chevrolet Colorado | Base, LS, LT, Sport, Sport LS, WT, Z71, Z71 LS, Z85, Z85 LS | 4 Cyl 2.8 L GAS, 4 Cyl 2.9 L GAS, 5 Cyl 3.5 L GAS, 5 Cyl 3.7 L GAS, 8 Cyl 5.3 L GAS
  • OEM 2010 Chevrolet Colorado Boot Kit, Front Wheel Drive Shaft Double Offset Joint (Outboard) - 89040355
    OEM 2010 Chevrolet Colorado Boot Kit, Front Wheel Drive Shaft Double Offset Joint (Outboard) Diagram - 89040355
    View Related Parts

    OEM (Genuine) 2010 Chevrolet Colorado Boot Kit, Front Wheel Drive Shaft Double Offset Joint (Outboard)

    PartNumber: 89040355
    Product Specifications
    • Notes: 4WD; Canyon, Colorado
    • Location: Driver Side; Passenger Side
    • Other Names: Inner Boot
    • Item Dimensions: 6.1 x 4.4 x 4.2 inches
    • Item Weight: 1.50 Pounds
    • Fitment Type: Direct Replacement
    • Part Description: 2010 Chevrolet Colorado Boot Kit, Front Wheel Drive Shaft Double Offset Joint (Outboard)
    More Info
    Vehicle Fitment
    • 2010 Chevrolet Colorado | Base, LS, LT, Sport, Sport LS, WT, Z71, Z71 LS, Z85, Z85 LS | 4 Cyl 2.8 L GAS, 4 Cyl 2.9 L GAS, 5 Cyl 3.5 L GAS, 5 Cyl 3.7 L GAS, 8 Cyl 5.3 L GAS

FAQ for Cv Joint Boot Repair

Q: How do you remove the wheel drive shaft inner joint and boot?
A:
You can place the driveshaft in a vise, slide the seal off the driveshaft, and remove the D/O joint housing, and the inner race.
By Omar
GM Specialist
16/03/2022
Q: What is the installation procedure for the wheel drive shaft outer joint and boot?
A:
The procedure is to pack the C/V joint, install the retaining clamp, and the inner seal.
By Omar
GM Specialist
15/03/2022
Q: What is the proper way to install the wheel drive shaft inner joint and boot?
A:
The proper way is to install the retaining clamp, the cage, and the seal, and secure the retaining clamp.
By Omar
GM Specialist
14/03/2022
Q: What is the proper way to remove the wheel drive shaft outer joint and boot?
A:
The proper way is to remove the inner seal, and the outer seal, and clean the old grease out of the C/V joint.
By Omar
GM Specialist
14/03/2022

FAQ for Other Repair Info

Q: How do you install the Rear Axle Shaft Seal and/or Bearing?
A:
Use the J23690 and the J8092 to install the Axle Bearing, and then use the J21128 to install the axle shaft seal, the axle shaft, the tire and wheel assembly, next fill the rear axle with axle lubricant, lastly, lower the vehicle.
Q: What is the differential carrier assembly installation procedure?
A:
First, lift the front Differential into position and install the mounting bracket to the differential housing. Install the vent hose, and the electric motor actuator and tighten them to 22 Nm. Next install the electrical connector, the front wheel drive shafts, and the front propeller shaft.
Q: What is the rear axle shaft installation procedure?
A:
Install the rear Axle Shaft, the C-lock to the rear axle, and the pinion shaft. Next, install the lock bolt and tighten it to 25 Nm. Install the rear brake drums from the vehicle and the rear axle housing cover and gasket. After that fill the rear axle with fluid.