< Back ×
My Vehicle Change Vehicle
2010 Chevrolet Impala
< Back to View All
Brake Boosters & Brake Master Cylinders
- Department
- Series
- Brands
- Prices
OEM (Genuine) 2010 Chevrolet Impala Master Cylinder
PartNumber: 22796285
Product Specifications- Notes: 2006-11, W/ABS
- Other Names: Master Cylinder
- Item Dimensions: 14.8 x 8.0 x 7.0 inches
- Item Weight: 1.60 Pounds
- Fitment Type: Direct Replacement
- Replaces: 25908489, 20885005, 20967783
- Part Description: 2010 Chevrolet Impala Master Cylinder
Vehicle Fitment- 2010 Chevrolet Impala | LS, LT, LTZ, Police, SS | 6 Cyl 3.5 L FLEX, 6 Cyl 3.5 L GAS, 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS, 6 Cyl 3.9 L FLEX, 8 Cyl 5.3 L GAS
$116.52 MSRP:$219.86You Save: $103.34 (48%)
Centric® Premium Brake Master Cylinder for 2010 Chevrolet Impala
PartNumber: 130.62173Product Specifications- UPC: 805890655008
- Part Description: 2010 Chevrolet Impala Premium Brake Master Cylinder
Vehicle Fitment- 2010 Chevrolet Impala | All Trims | All Engines
$95.03
Cardone Reman® Remanufactured Master Cylinder for 2010 Chevrolet Impala
PartNumber: 10-3996Product Specifications- Notes: Supplied w/o Reservoir
- Bore Diameter (N): 1.00"
- E-Waste: No
- Installation Hardware Included: No
- Master Cylinder Color/Finish: Gray
- Master Cylinder Material: Aluminum
- Mounting Hole Quantity: 2
- Package Contents: Master Cylinder
- Port Quantity: 2
- Primary Port Size: M14 x 1.5
- Product Condition: Remanufactured
- Reservoir Included: No
- Secondary Port Size: M14 x 1.5
- UPC: 082617888882
- Part Description: 2010 Chevrolet Impala Remanufactured Master Cylinder
Vehicle Fitment- 2010 Chevrolet Impala | All Trims | All Engines
FAQ for Brake Master Cylinder Repair
Q: How do I install the Master Cylinder Reservoir?
A:
Clean the reservoir. Dry the reservoir with non-lubricated, filtered air. Lubricate the new seals and the outer surface area of the reservoir-to-housing barrels. Install the lubricated seals and the reservoir to the master cylinder. Tap the reservoir retaining pins into place to secure the reservoir. Install the sensor into the reservoir and remove the master cylinder from the vice and install it in the vehicle.
By Bob
GM Specialist
30/03/2022Q: How do I install the Master Cylinder?
A:
Start with bench bleeding the master cylinder. Install the master cylinder to the vacuum brake booster and the master cylinder mounting nuts. Remove the plugs from the brake pipes. Connect the brake pipes to the master cylinder and the electrical connector to the brake fluid level sensor. Bleed the brake system.
By Omar
GM Specialist
30/03/2022Q: How do I prevent system contamination?
A:
Prevent contamination by plugging the hose ends.
By Omar
GM Specialist
29/03/2022Q: How do I remove the Master Cylinder Reservoir?
A:
Start with removing the master cylinder from the vehicle. Then secure the master cylinder in a vise. Then remove the brake fluid level sensor. Carefully tap out the reservoir retaining pins. Next, remove the reservoir and seals from the master cylinder,.
By Omar
GM Specialist
29/03/2022Q: How do I remove the Master Cylinder?
A:
Start with disconnecting the electrical connector from the brake fluid level sensor and the brake pipes from the master cylinder. Plug the open brake pipe ends. Remove the master cylinder mounting nuts and then the master cylinder from the vehicle. Drain the master cylinder reservoir of all brake fluid.
By Bob
GM Specialist
29/03/2022Q: How much fluid should be in the cylinder reservoir when performing the bench bleeding?
A:
The reservoir should be filled at least to the halfway mark.
By Bob
GM Specialist
27/03/2022Q: What if the brake fluid level is below the half mark on the reservoir?
A:
The brake system should be inspected for wear and possible brake fluid leaks.
By Omar
GM Specialist
26/03/2022Q: What should be used to clean the brake master cylinder bore?
A:
Use denatured alcohol or equivalent, and avoid using abrasives to clean the brake master cylinder bore.
By Bob
GM Specialist
22/03/2022Q: What should I use to grease the master cylinder bore, the secondary piston, and the return spring?
A:
Grease with Delco supreme 1 or equivalent DOT-3 brake fluid from a clean, sealed brake fluid container.
By Omar
GM Specialist
22/03/2022Q: Which hoses will need to be removed from the master cylinder?
A:
You will need to remove the transparent hoses.
By Bob
GM Specialist
21/03/2022See more FAQs (5)