< Back ×
My Vehicle Change Vehicle
2010 Chevrolet Traverse
< Back to View All
A/C & Heating
- Department
- Prices
OEM (Genuine) 2010 Chevrolet Traverse Heater Core
PartNumber: 84406079
Product Specifications- Notes: Rear; Enclave, Traverse
- Other Names: Heater Core
- Item Dimensions: 9.3 x 8.4 x 3.4 inches
- Item Weight: 1.20 Pounds
- Fitment Type: Direct Replacement
- Replaces: 15232212
- Part Description: 2010 Chevrolet Traverse Heater Core
Vehicle Fitment- 2010 Chevrolet Traverse | High Country, L, LS, LT, LTZ, Premier, RS | 4 Cyl 2.0 L GAS, 6 Cyl 3.6 L GAS
$85.85 MSRP:$162.00You Save: $76.15 (48%)
OEM (Genuine) 2010 Chevrolet Traverse Heater Core
PartNumber: 22961456
Product Specifications- Notes: Front, W/O Auto Temp Control; Front, W/Auto Temp Control
- Location: Passenger Side; Driver Side
- Other Names: Heater Core
- Item Dimensions: 15.2 x 8.3 x 4.5 inches
- Item Weight: 1.60 Pounds
- Fitment Type: Direct Replacement
- Replaces: 22782131, 20843382, 25786439, 20829256
- Part Description: 2010 Chevrolet Traverse Heater Core
Vehicle Fitment- 2010 Chevrolet Traverse | LS, LT, LTZ, Premier | 6 Cyl 3.6 L GAS
$140.37 MSRP:$264.86You Save: $124.49 (48%)
FAQ for Heater Core Repair
Q: What is the recommended torque for heater core cover screws?
A:
The recommended torque is 3 Nm (27 lb in).
By Bob
GM Specialist
01/11/2022Q: What is the preliminary procedure for servicing the heater core?
A:
The procedure is to remove the heater core tubes from the heater core, and cap or plug the heater core and tube openings to prevent spillage of fluids upon removal.
By Bob
GM Specialist
01/11/2022Q: How to service the heater core?
A:
You shall reposition the heater core outward from the heater case, mark the location of the center foam seal, press on foam seals to activate adhesive, and push the heater core until the foam seal around the heater core tank is inserted into the HVAC module and the heater core is fully seated.
By Bob
GM Specialist
01/11/2022Q: What is the preliminary procedure for servicing the auxiliary heater core?
A:
The procedure is to remove the HVAC module auxiliary, disconnect any wiring connectors or harnesses from the HVAC module, and remove evaporator tube retaining dips before removing the lower gasket and cover.
By Bob
GM Specialist
01/11/2022Q: What is the preliminary procedure for servicing the heater core cover?
A:
The procedure is to remove the left front floor console extension panel and the floor outlet air duct and reposition any wiring harness to access the heater core cover.
By Bob
GM Specialist
01/11/2022Q: How many bolts does the auxiliary HVAC Module lower cover attach?
A:
It attaches 3 bolts.
By Bob
GM Specialist
01/11/2022Q: What is the recommended torque for auxiliary HVAC Module lower cover bolts?
A:
The recommended torque is 3 N.m (27 lb in).
By Bob
GM Specialist
01/11/2022Q: How many screws does the heater core cover attach?
A:
It attaches 3 screws.
By Bob
GM Specialist
01/11/2022Q: How many screws attach to the Heater Core Cover?
A:
3screws attach to the heater core cover.
By Omar
GM Specialist
09/03/2022Q: Q. how do I install the Heater Core?
A:
You will need to reposition the heater core outward from the heater case to ease the removal. Mark the location of the foam seal from the old heater core. Then press on the seals to activate the adhesive and keep the core straight and horizontal when inserting it into the HVAC Module. Lastly, push the heater core until the foam seal around the heater core tank is inserted into the HVAC module.
By Bob
GM Specialist
09/03/2022See more FAQs (9)