Contact Us Live Chat or 1-888-220-8330
Search Bar
Search by Part Number or Keywords
  • My Garage
  • My Account
  • Cart
  • Body & Mirrors
  • Chassis & Brakes
  • Engine & Drivetrain
  • Electrical & Lighting
Help Center
< Back ×
  • Body & Mirrors
  • Chassis & Brakes
  • Engine & Drivetrain
  • Electrical & Lighting
Login/Register My Account Track Order Help Center Contact Us
Replacement and OEM Parts for 2001 Chevrolet Metro ABS Control Module

2001 Chevrolet Metro ABS Control Module

My Vehicle Change Vehicle
2001 Chevrolet Metro
Change Vehicle
Vehicle Options
We need more information about your vehicle to make a correct determination of fitment
< Back to View All
ABS & Parking Brake
  • Department
  • Prices

1 Product found

4 Q&A for Abs Control Module Repair
Show Item:
  • 30
  • 60
  • 90
Sort by:
Recommended
Filter
Sort
View by
  • OEM 2001 Chevrolet Metro ABS Control Unit Repair Kit Diagram - 91172172
    View Related Parts

    OEM (Genuine) 2001 Chevrolet Metro ABS Control Unit Repair Kit

    PartNumber: 91172172
    OEM 2001 Chevrolet Metro ABS Control Unit Repair Kit - 91172172
    Product Specifications
    • Notes: Control Unit
    • Other Names: ABS Control Unit Repair Kit, Motor, Motor Assembly
    • Item Dimensions: 5.5 x 10.2 x 4.4 inches
    • Item Weight: 5.30 Pounds
    • Fitment Type: Direct Replacement
    • Part Description: ABS Control Unit Repair Kit
    More Info
    $313.30 MSRP: $591.16
    You Save: $277.86 (48%)

FAQ for Abs Control Module Repair

Q: How to install the electronic brake control relay?
A:
You need to install the Electronic Brake Control Relay into the underhood electrical center and the under hood Electrical Center cover, close the hood and perform A Diagnostic System Check-ABS.
By Bob
GM Specialist
01/11/2022
Q: What is the removal procedure for the electronic brake control module (EBCM)?
A:
You need to remove two screws and disconnect the electrical connectors and then remove the junction block from the instrument panel, disconnect the EBCM electrical connectors, remove the three bolts and remove the EBCM.
By Bob
GM Specialist
01/11/2022
Q: What is the recommended torque for the attaching bolts?
A:
The recommended torque is 8 Nm (71-inch lbs.).
By Bob
GM Specialist
01/11/2022
Q: What is the removal procedure for the electronic brake control relay?
A:
You need to open the hood, remove the under hood Electrical Center cover, and remove the Electronic Brake Control Relay from the underhood electrical center.
By Bob
GM Specialist
01/11/2022

FAQ for Other Repair Info

Q: What is the removal procedure for the parking brake cable?
A:
You need to remove the parking brake lever trim bezel, loosen the adjuster nut on the parking brake lever assembly, remove the Parking Brake Cable from the parking brake lever assembly equalizer plate, raise and support the vehicle, remove the rear tire and wheel assemblies, the two guide brackets from the cable, the cable grommet, the drums, and the parking brake cable, and squeeze the parking brake cable retainer, and remove the parking brake cable from the backing plate.
Q: What is the removal procedure for the steering knuckle?
A:
You need to raise and support the vehicle, remove the tire and wheel assembly, the brake caliper, the caliper carrier, the rotor, the wheel speed sensor electrical connector, the one bolt, and the wheel speed sensor, and remove and remove the drive axle nut and washer, remove the hub, the cotter pin, and the castle nut, the tie rod end, the ball stud nut and bolt, the two strut-to-knuckle bolts and nuts and the Steering Knuckle.
Q: What is the disassembly procedure for the wheel cylinder overhaul?
A:
You need to disassemble the boots, the pistons, the cup seals, the spring, and the bleeder valve, clean the Wheel Cylinder body in clean brake fluid, dry the wheel cylinder body, and inspect the wheel cylinder body, the piston, the cup seals and the spring.