< Back ×
2002 Buick Park Avenue Intake Manifold
My Vehicle Change Vehicle
2002 Buick Park Avenue
< Back to View All
Air Filters & Intake Systems
- Department
- Brands
- Prices
OEM (Genuine) 2002 Buick Park Avenue Manifold
PartNumber: 24503488$6.91 MSRP:$11.44You Save: $4.53 (40%)Product Specifications- Notes: 1998-05
- Other Names: Manifold
- Item Dimensions: 3.2 x 2.2 x 2.2 inches
- Item Weight: 0.40 Pounds
- Fitment Type: Direct Replacement
- Part Description: 2002 Buick Park Avenue Manifold
Vehicle Fitment- 2002 Buick Park Avenue | Base, Ultra | 6 Cyl 3.8 L GAS
Product Specifications- Notes: Gaskets Included
- Air Conditioning Compressor Mount: No
- Alternator Mount: No
- Color: Black
- EGR Ready: Yes
- Gasket or Seal Included: Yes
- Grade Type: Regular
- Heated Choke Port: No
- High-Riser: No
- Intake Manifold Material: Plastic
- Manifold Height: 6.5"
- Material: Plastic
- OE Part Number: 12537425, 24506013, 89017272, 89017274
- Plenum Style: Single Plane
- Port Outlet Dimensions: 36 x 45 mm
- Port Quantity: 6
- UPC: 019495033936
- Part Description: 2002 Buick Park Avenue Plastic Intake Manifold
Vehicle Fitment- 2002 Buick Park Avenue | All Trims | 6 Cyl 3.8L
Product Specifications- Air Conditioning Compressor Mount: No
- Alternator Mount: No
- Color: Silver
- EGR Ready: No
- Gasket or Seal Included: No
- Grade Type: Regular
- Heated Choke Port: No
- High-Riser: No
- Intake Manifold Material: Aluminum
- Manifold Height: 5"
- Material: Aluminum
- OE Part Number: 24508923, 19417844
- Plenum Style: Single Plane
- Port Quantity: 6
- UPC: 019495095071
- Part Description: 2002 Buick Park Avenue Aluminum Intake Manifold
Vehicle Fitment- 2002 Buick Park Avenue | All Trims | 6 Cyl 3.8L
Product Specifications- Air Conditioning Compressor Mount: No
- Alternator Mount: No
- Color: Aluminum
- EGR Ready: No
- Gasket or Seal Included: No
- Grade Type: Regular
- Heated Choke Port: No
- High-Riser: No
- Intake Manifold Material: Aluminum
- Manifold Height: 3"
- Material: Aluminum
- OE Part Number: 24505729
- Plenum Style: Single Plane
- Port Outlet Dimensions: 2 x 1.5"
- Port Quantity: 6
- UPC: 019495452867
- Part Description: 2002 Buick Park Avenue Aluminum Intake Manifold
Vehicle Fitment- 2002 Buick Park Avenue | All Trims | 6 Cyl 3.8L
Product Specifications- Notes: Park Avenue; W/Supercharger
- Other Names: Intake Manifold, Manifold
- Item Dimensions: 19.6 x 12.8 x 5.5 inches
- Item Weight: 12.90 Pounds
- Fitment Type: Direct Replacement
- Part Description: 2002 Buick Park Avenue Manifold Asm-Lower Intake
Vehicle Fitment- 2002 Buick Park Avenue | Base, Ultra | 6 Cyl 3.8 L GAS
Product Specifications- Notes: Park Avenue; W/O Supercharger; Lower
- Other Names: Intake Manifold
- Item Dimensions: 6.2 x 26.3 x 13.7 inches
- Item Weight: 12.70 Pounds
- Fitment Type: Direct Replacement
- Replaces: 24505728, 24508923
- Part Description: 2002 Buick Park Avenue Intake Manifold
Vehicle Fitment- 2002 Buick Park Avenue | Base, Ultra | 6 Cyl 3.8 L GAS
FAQ for Intake Manifold Repair
Q: What is the recommended torque for the throttle body nuts?
A:
The recommended torque is 10 Nm (89-inch lbs.).
By Bob
GM Specialist
01/11/2022Q: How to remove the intake manifold- lower?
A:
You need to remove the upper intake manifold and the thermostat housing, disconnect the electrical connector from the ECT, then remove the drive belt tensioner, the EGR valve outlet pipe, the lower intake manifold bolts, and the lower intake manifold, and clean and inspect the lower intake manifold finally.
By Bob
GM Specialist
01/11/2022Q: What is the proper way to install the fuel injector sight shield?
A:
You should align the extension on the rear edge of the shield to the bracket on the rear of the engine, then push the shield rearward and push down to align it with the oil filler hole, and finally, install the oil filler neck.
By Bob
GM Specialist
01/11/2022Q: What is the recommended torque for the lower intake manifold bolts?
A:
The recommended torque is 15 Nm (11 ft. lbs.).
By Bob
GM Specialist
01/11/2022Q: What should be noticed before installing the upper intake manifold?
A:
You should not use any sealer on the gasket.
By Bob
GM Specialist
01/11/2022Q: What is the recommended torque for the engine wiring harness heat shield fasteners?
A:
The recommended torque is 10 Nm (89-inch lbs.).
By Bob
GM Specialist
01/11/2022Q: How to remove the fuel injector sight shield?
A:
You need to remove the oil filler neck, lift the front of the shield up and pull towards the front of the vehicle, then remove the fuel injector sight shield.
By Bob
GM Specialist
01/11/2022See more FAQs (2)