< Back ×
My Vehicle Change Vehicle
2005 Buick Century
< Back to View All
Hoods
- Department
- Prices
OEM (Genuine) 2005 Buick Century Latch
PartNumber: 10423017
Product Specifications- Other Names: Latch, Lock
- Item Dimensions: 7.6 x 6.3 x 4.4 inches
- Item Weight: 0.50 Pounds
- Fitment Type: Direct Replacement
- Replaces: 10255215
- Part Description: 2005 Buick Century Latch
Vehicle Fitment- 2005 Buick Century | Custom, Limited, Special Edition | 6 Cyl 3.1 L GAS
$35.74 MSRP:$53.93You Save: $18.19 (34%)
OEM (Genuine) 2005 Buick Century Latch
PartNumber: 10445387
Product Specifications- Other Names: Latch, Lock
- Item Dimensions: 10.3 x 6.3 x 2.8 inches
- Item Weight: 1.20 Pounds
- Fitment Type: Direct Replacement
- Part Description: 2005 Buick Century Latch
Vehicle Fitment- 2005 Buick Century | Custom, Limited, Special Edition | 6 Cyl 3.1 L GAS
FAQ for Hood Latch Repair
Q: How do you remove the Hood Latch Support?
A:
You need to open the hood and remove the hood latch from the hood latch support bracket, the front bumper fascia bracket from the hood latch support, the bolts from the hood latch support bracket at the upper tie bar, the nut from the hood latch support bracket at the lower tie bar and the hood latch support bracket from the vehicle.
By Bob
GM Specialist
01/11/2022Q: How do you remove the Hood Latch Release Handle?
A:
You need to remove the instrument panel insulator, the bolts from the hood latch release handle, the hood release cable from the hood release handle, and the hood release handle from the instrument panel.
By Bob
GM Specialist
01/11/2022Q: How do you install the Hood Latch Release Handle?
A:
You need to install the hood release cable to the hood release handle, the hood release handle to the instrument panel, the bolts to the hood latch release handle, and the instrument panel insulator.
By Bob
GM Specialist
01/11/2022Q: How do you install the Seal-Plenum to the Hood?
A:
You need to align the weatherstrip to the flange. Starting at the passenger side corner, you can press the weatherstrip onto the flange, work toward the center of the car and close the hood.
By Bob
GM Specialist
01/11/2022Q: What is the recommended torque for the fender bolts?
A:
The recommended torque is 25 Nm (18 lb-ft).
By Bob
GM Specialist
01/11/2022Q: How do you remove the Hood Hinge?
A:
You need to remove the hood, the hood assists rod, and the hood rear side seals from the hood hinge, loosen the hood hinge to the fender bolts but do not remove the bolts, center punches the spot weld, drill out the spot weld, remove the hood hinge to fender bolts and the hood hinge from the fender and repair the paint on the fender where the door hinge was removed.
By Bob
GM Specialist
01/11/2022Q: How do you install the Hood Latch Support?
A:
You need to install the hood latch support to the vehicle, the bolts to the hood latch support at the upper tie bar, the nut to the hood latch support at the lower tie bar, the front bumper fascia bracket to the hood latch support and the hood latch to the hood latch support bracket.
By Bob
GM Specialist
01/11/2022Q: How do you install the Hood Latch?
A:
You need to connect the hood latch release cable to the hood latch, position the hood latch to the marks on the hood latch support bracket, install the hood latch to center support bracket bolts, adjust the hood, as required, and close the hood.
By Bob
GM Specialist
01/11/2022Q: How do you remove the Seal-Hood Rear Side?
A:
You need to open the hood, remove the rear side hood seal from the pinch-weld flange and motor compartment flange and the rear side hood seal from the vehicle, and clean any adhesive from the pinch-weld flange and motor compartment flange surface using 3M(TM) P/N 8984 adhesive remover.
By Bob
GM Specialist
01/11/2022Q: How do you remove the Seal-Plenum to the Hood?
A:
You need to open and support the hood. Starting at the center of the weatherstrip, you can pull the weatherstrip forward and pull the weatherstrip off of the flange, and remove the weatherstrip from the flange.
By Bob
GM Specialist
01/11/2022See more FAQs (12)